Results 1 to 11 of 11
  1. #1
    RC poster
    Join Date
    Aug 2012
    Posts
    6

    Traxxas E-Revo 1/16 VXL Problem Please Help

    Hi, I have one problem with E-Revo 1/16 Brushless... Wel lthe problem is when i hammer the gas down it doesnt want to move if i press slowly than its starts to move but when i press gas to full it doesnt want to move... Can you please help me i am getting bored becouse i didnt drive it for like 1 month...

    Video of the problem:
    http://www.youtube.com/watch?v=AEAOr5hA8Fg

  2. #2
    RC Turnbuckle Jr. Petertje60's Avatar
    Join Date
    Jan 2011
    Location
    Rotterdam, Netherlands
    Posts
    7,610
    Does it go up to full rpm when you pull the throttle slowly?
    Recalibrating might be worth to try.
    Nobody is born with experience

  3. #3
    RC Competitor
    Join Date
    May 2012
    Location
    Portugal
    Posts
    62
    Yap, try to recalibrate it.

  4. #4
    RC poster
    Join Date
    Aug 2012
    Posts
    6
    I just tried recalibrating it but its same if i hammer it down it wont blink if i press slowly it does... Maybe the transmitter is dead?
    Last edited by mansy; 08-30-2012 at 03:11 PM.

  5. #5
    RC Champion
    Join Date
    Jun 2004
    Posts
    1,894
    I'd call Traxxas Support, it could be a messed up ESC.
    ***You Build It ...I'll Jump It!!!*** OS .18 TZ; Trinity Pipe; HCR Titanium Skid Plates & Bumpers; Futaba S9450 Throttle Servo; Airtronics 94358Z Steering Servo; RPM A-arms & Knuckles; FOC; Lunsford Titanium Hinge Pins,Turnbuckles, Push Rods & Rocker Posts; New Era Roll Bar & Engine Mount; Proline Mashers on Velocity Rims.

  6. #6
    RC poster
    Join Date
    Aug 2012
    Posts
    6
    Well its kinda hard for me i live in Slovenia so its kinda hard to contact Traxxas Support... But i think that transmitter is dead it wont blink if i hammer down if i press slowly it will when i end calibrating it its same it wont move if i hammer down... Transmitter dead maybe?

  7. #7
    RC Competitor
    Join Date
    May 2012
    Location
    Portugal
    Posts
    62
    If itīs not the servo... Have you opened the receiver box and unplug and plugged the wires again? Or have you touched the conectors inside the receiver?

  8. #8
    RC Turnbuckle Jr. Petertje60's Avatar
    Join Date
    Jan 2011
    Location
    Rotterdam, Netherlands
    Posts
    7,610
    Are you able to try a different battery?
    Nobody is born with experience

  9. #9
    RC poster
    Join Date
    Aug 2012
    Posts
    6
    I have new one and new charger... Battery is same as original one I bought it when the problem was i thought that it will help but it didnt...

  10. #10
    RC poster
    Join Date
    Aug 2012
    Posts
    6
    I unplugged every wire attached in reciver box the servo and everything but it just wont help... Yesterday i tried Recalibrating it but its same as always so I think maybe the transmitter is dead...

  11. #11
    RC Turnbuckle Jr.
    Join Date
    Mar 2012
    Location
    so cal
    Posts
    9,244
    Sounds like a bad esc

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •