Results 1 to 14 of 14
  1. #1
    RC Competitor
    Join Date
    May 2014
    Posts
    83

    SCT body on my ERBE

    So I hacked up a Proline Silverado HD SCT body to work on my erbe. It turned out far better than I was expecting considering this is the first body I've worked on since being out of the RC hobby for about 12 years.

    The body is still clear so pics don't show a lot of detail. Still need to do a bit of edge sanding. I will post some update pics once I pait. I also have a few tricks up my sleeve for this body!










  2. #2
    RC Competitor
    Join Date
    May 2014
    Posts
    83
    A few update shots. Still a good amount of work to do on this body.





    Last edited by silveroneone; 05-25-2014 at 09:35 PM.

  3. #3
    RC Racer
    Join Date
    Nov 2013
    Location
    Missouri
    Posts
    229
    Looks good
    Slash 4x4 & E-revo brushless

  4. #4
    RC Qualifier
    Join Date
    Feb 2009
    Posts
    784
    I like it. Looks nice.
    If it didn't break you can do it again.

  5. #5
    RC Turnbuckle Jr. 87 GN's Avatar
    Join Date
    Mar 2010
    Location
    kansas
    Posts
    8,382
    any reason you have your tires on backwards? But that does look good, nice and clean pain job.
    Would you go flip my truck back over??

  6. #6
    RC Competitor
    Join Date
    May 2014
    Posts
    83
    Quote Originally Posted by 87 GN View Post
    any reason you have your tires on backwards? But that does look good, nice and clean pain job.
    Lol, no, I I thought someone might comment on that. No reason, just was not paying attention after I cleaned it,

  7. #7
    RC Competitor
    Join Date
    May 2014
    Posts
    83
    Did a little work on the body today. 4in RC4WD led light bar mounted on front grill. I have a 6in on the way as well. Crazy how much light these little bars push out!





    Last edited by silveroneone; 05-26-2014 at 10:09 PM.

  8. #8
    RC Qualifier
    Join Date
    Sep 2008
    Location
    Turks and Caicos Islands, BWI
    Posts
    623
    Dem lights kool!
    Ray00
    E–Revo │ E-Revo BE
    ITCHY THROTTLE FINGER!

  9. #9
    RC Competitor
    Join Date
    Jul 2012
    Posts
    67
    Very **** badarse! 'Specially that light bar. Are you going to do tail lights?
    Also, have you ran into anything nose or tail first with it? Just wondering about the bumper-less front and rear and how the body might be affected.

  10. #10
    RC Turnbuckle Jr. Jezza's Avatar
    Join Date
    Feb 2013
    Location
    Montreal, Canada
    Posts
    3,433
    Man that looks good, love the light bar.
    Live life to the fullest

  11. #11
    RC Competitor
    Join Date
    May 2014
    Posts
    83
    Quote Originally Posted by Deisel View Post
    Very **** badarse! 'Specially that light bar. Are you going to do tail lights?
    Also, have you ran into anything nose or tail first with it? Just wondering about the bumper-less front and rear and how the body might be affected.
    I am not quite finished with the body yet so I have not run it. I have a set of nitro Slash bumpers that are a direct fit on the Revo. Going to modify those a bit to run with this body. As far as tails, yeah, but still not sure what kind of set up.

  12. #12
    RC Competitor
    Join Date
    May 2014
    Posts
    83
    Finally got the 6" mounted up.

    I only run the light bars when running at night at "low speeds". I can remove both light bars in about 30sec, so it's a quick swap in and out.







    I'll try to get some night pics with these bad boys turned on. I run each bar off its own 2s 7.4v 430nAh.
    86 L.E.Ds total!
    Last edited by silveroneone; 06-06-2014 at 08:13 PM.

  13. #13
    RC Competitor
    Join Date
    Feb 2012
    Posts
    86
    Looks sick dude!!

  14. #14
    RC Competitor
    Join Date
    Jul 2012
    Posts
    67
    ! !

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •