Search:

Type: Posts; User: dank_ebola

Page 1 of 7 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    16
    Views
    1,345

    The OS .21tm FOR REVO is a direct drop in with no...

    The OS .21tm FOR REVO is a direct drop in with no mods if youre directly replacing a bone stock 3.3 mill
  2. Replies
    9
    Views
    2,435

    What about hi-temp flexible tubing (ie for hot...

    What about hi-temp flexible tubing (ie for hot water in your sink)?
  3. Replies
    5
    Views
    1,026

    counterclockwise, same as HSN

    counterclockwise, same as HSN
  4. Replies
    20
    Views
    1,238

    My non-traxxas motor seems to run best at around...

    My non-traxxas motor seems to run best at around 280. Any richer than that and its poo. Not burning up plugs either. I think that could be from a leak in the carb and front bearing too (which will be...
  5. Replies
    6
    Views
    1,009

    That happened to me too. Sounds like thats...

    That happened to me too. Sounds like thats probably what happened. You would need a new bearing, and a ring and pinion gear.
  6. Thread: Bearings

    by dank_ebola
    Replies
    8
    Views
    862

    Thanks for the suggestions, I will keep all in...

    Thanks for the suggestions, I will keep all in mind. Thanks again.
  7. Thread: Bearings

    by dank_ebola
    Replies
    8
    Views
    862

    Are they good bearings though? I guess at a...

    Are they good bearings though? I guess at a dollar each they can be pretty expendable but dollars add up quick; especially with my recent luck in bad bearings.
  8. Replies
    31
    Views
    4,431

    I was searching on ebay this weekend and found a...

    I was searching on ebay this weekend and found a .21tm for around $250 brand new with Revo header. The only other thing I would recommend but you may not need is the Traxxas spring mount exhaust...
  9. Thread: Bearings

    by dank_ebola
    Replies
    8
    Views
    862

    Bearings

    After a miserable Saturday (pull starter broke on first pull :mad: ) I decided I would do a little maintenance work on my Revo. First I went to replace the rear a-arms and noticed when I pulled apart...
  10. My youtube name is easymackn. I havent had a...

    My youtube name is easymackn. I havent had a chance to upload alot of the new videos we have because theyre on another PC at my friends house. When I'm over there this weekend I will upload them.
  11. YES!! I will try to get some of one of our...

    YES!! I will try to get some of one of our buddy's 8ight 2.0 and our Revos going at it this weekend and put them on my channel.
  12. .21TM!!! Have it and love it. Its a beast. Easy...

    .21TM!!! Have it and love it. Its a beast. Easy to tune and holds it really well. I haven't had to touch a needle in 6 tanks (3 days worth of running) and still keeping it well under 270F. Ive got...
  13. Replies
    6
    Views
    1,038

    http://www.tonysscrews.com/product.sc?productId=6&...

    http://www.tonysscrews.com/product.sc?productId=6&categoryId=61

    Got a set from him. Sorted in small baggies.
  14. Replies
    5
    Views
    1,309

    its not damaged or anything and theres only...

    its not damaged or anything and theres only enough fuel through it from break in?
  15. Replies
    5
    Views
    1,309

    How are you tightening the cooling head bolts...

    How are you tightening the cooling head bolts down? Youre supposed to do it in a star pattern similar to how you would tighten lugs on a car tire. If you accidentally tightened one side down all the...
  16. Replies
    7
    Views
    841

    We were told by Traxxas support to keep it at or...

    We were told by Traxxas support to keep it at or around (within 10F) of 270F. They claim that even though the head is reading 250F or lower the internals are hotter and can cause excessive...
  17. Replies
    7
    Views
    1,007

    I kind of like the track. I think its all in the...

    I kind of like the track. I think its all in the operator of the rig. The BBs are definitley more powerful and I will admit that they can be faster but I can outrun a BB as long as I concentrate on...
  18. Replies
    9
    Views
    850

    Not much help on new servos but if you wanted to...

    Not much help on new servos but if you wanted to save a few bucks, if you have a good stock steering servo then take that and use it for the T/B servo. Its a decent cost effective upgrade considering...
  19. Replies
    12
    Views
    1,171

    Seems like the horse must have a beef w/Traxxas....

    Seems like the horse must have a beef w/Traxxas. Sell the horse to a glue factory to get your money back.
  20. Replies
    3
    Views
    765

    http://rbmods.net/rbshop/index.php?target=products...

    http://rbmods.net/rbshop/index.php?target=products&product_id=171
  21. Replies
    8
    Views
    1,196

    Might also want to check to make sure that your...

    Might also want to check to make sure that your clutch bell teeth are in good shape too.
  22. Replies
    5
    Views
    923

    Apparently it will. I asked the same thing a...

    Apparently it will. I asked the same thing a couple weeks ago.
  23. Replies
    17
    Views
    1,190

    Best thing to do is take your exhaust header off...

    Best thing to do is take your exhaust header off or your plug out if you dont want to remove the mill and rotate the flywheel until it has reached BDC (bottom dead center) and mark with a sharpie on...
  24. Replies
    19
    Views
    1,227

    Switch to a hotter plug perhaps; like an LC3? ...

    Switch to a hotter plug perhaps; like an LC3?

    What about making sure the throttle linkage is setup correctly?
  25. Replies
    19
    Views
    1,227

    Did you check between the pads and the brake...

    Did you check between the pads and the brake rotor and make sure that those werent rubbing?
Results 1 to 25 of 156
Page 1 of 7 1 2 3 4