Search:

Type: Posts; User: malonefamily2003

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Had a similar situation happen to me 2 days ago....

    Had a similar situation happen to me 2 days ago. My son parked his Stampede for 10 minutes without unplugging or turning it off. I noticed the smoke and quickly unplugged the battery . Pretty much...
  2. Replies
    15
    Views
    221

    Try a slightly bigger allen wrench (US standard...

    Try a slightly bigger allen wrench (US standard size not metric) plus lots of heat.
  3. Replies
    15
    Views
    221

    It could also be a stripped allen wrench. I have...

    It could also be a stripped allen wrench. I have to cut the very tip off mine from time to time. Try heating the hex nut near the pin to loosen the Loctite it should come right out.
  4. Replies
    588
    Views
    57,361

    http://i823.photobucket.com/albums/zz155/malonefam...

    http://i823.photobucket.com/albums/zz155/malonefamily2003/FullSizeRender13_zpswcuyb2i7.jpg
    Made some improvements to one of my trailers . Its now 2 inches wider has a wooden floor, several tie downs...
  5. Replies
    588
    Views
    57,361

    Ok so I dropped the Tx out of the back of my SUV...

    Ok so I dropped the Tx out of the back of my SUV and when I picked it up it made a loud rattling sound. Some small silver metal square thing (outlined in red)had broken off so I soldered it back on....
  6. Replies
    14
    Views
    214

    Not hard to do but can be annoying when they...

    Not hard to do but can be annoying when they start buzzing. They need realigned from time to time. There are some good videos on You Tube to show you how to set them up.
  7. Replies
    14
    Views
    214

    You could do that but will still have alignment...

    You could do that but will still have alignment issues. Like BRICK said single servo setup really is the way to go if your gonna upgrade. If your running in lots of deep water then waterproof is a...
  8. Replies
    14
    Views
    214

    The 1230 is not waterproof but can be made...

    The 1230 is not waterproof but can be made waterproof easily . I run the 1230 on both my Summits. The 0231wp is too weak for the single servo mod
  9. Replies
    14
    Views
    214

    I find its best to replace both servos at once....

    I find its best to replace both servos at once. Its a chain reaction when one goes bad if not caught quickly it will overheat and damage the other servo. The flashing lights and other weird stuff is...
  10. Replies
    4
    Views
    165

    There's no need to take the tranny apart. The...

    There's no need to take the tranny apart. The shift pin has a small rubber boot you can slide forward . Put some lube on the pin while shifting the tranny by hand. If that doesn't work then try...
  11. Replies
    588
    Views
    57,361

    Very disappointed with the look after mounting...

    Very disappointed with the look after mounting the Cyclones and Rock Crushers. Gonna run them for a month just so the wife doesn't find out then put the Swampers back on. Good news is the diff and...
  12. Replies
    4
    Views
    165

    I would try adding some lube to the shift pin on...

    I would try adding some lube to the shift pin on the tranny then work it by hand a few times.
  13. Replies
    588
    Views
    57,361

    About 3 weeks ago I removed the Mudslingers from...

    About 3 weeks ago I removed the Mudslingers from the wide Axial rims and mounted them on the narrow Axial rims. The Mudslingers looked so much better now that I cut a little over an inch out of 1 of...
  14. Replies
    588
    Views
    57,361

    These gears are softer steel compared to the...

    These gears are softer steel compared to the stock gears. The teeth are shorter and don't mesh correctly with stock pinion. On 1 gear the 4 small holes were so narrow the bolts had to be threaded...
  15. Replies
    588
    Views
    57,361

    If anyone has thought about buying the hardened ...

    If anyone has thought about buying the hardened steel ring gears from Rcdamper on EBay don't waste your time or money. Just bought 2 and both are unusable. Ordered the stock Traxxas gears and gonna...
  16. Replies
    25
    Views
    525

    You should already have the 5344x spring . Unless...

    You should already have the 5344x spring . Unless you have a really old summit it comes stock now days .
  17. Replies
    2
    Views
    170

    Tried that but didn't like the taste of diff oil.

    Tried that but didn't like the taste of diff oil.
  18. Replies
    2
    Views
    170

    Summit diff gear questions?

    Does anyone know what type of steel the Summit diff gears are made of? Is it possible that the gears are already hardened steel ? I had always assumed the ring gear and spider gears were made of...
  19. Replies
    588
    Views
    57,361

    Cyclone Alumnium 40 series bead locks from RC4WD...

    Cyclone Alumnium 40 series bead locks from RC4WD . They are discontinued so hard to find.
  20. Replies
    588
    Views
    57,361

    The new wheels and tire came today. Had to add...

    The new wheels and tire came today. Had to add some Ford logos .
    http://i823.photobucket.com/albums/zz155/malonefamily2003/FullSizeRender7_zps4qxlcp8k.jpg
  21. Replies
    13
    Views
    287

    I agree 98% to what KSB said but it all boils...

    I agree 98% to what KSB said but it all boils down to the proper clutch setup. There are a few situations where hi gear could help but most times it is much harder on the drivetrain. At times the...
  22. Replies
    588
    Views
    57,361

    I had just bought some Rock Crushers a month ago...

    I had just bought some Rock Crushers a month ago but couldn't pass on the RC4WD beadlocks. With 16 people watching the listing I expected a bidding war but I was the only bidder....
  23. Replies
    588
    Views
    57,361

    10 hours and counting down?

    10 hours and counting down?
  24. May just be me but I tose the Teflon washer out...

    May just be me but I tose the Teflon washer out and replace with shims.
  25. Replies
    588
    Views
    57,361

    Well worth the money . I haven't had any issues...

    Well worth the money . I haven't had any issues with spider gears since installing the LEM diff cups. Now if we could just get them to make hardened ring gears.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4