Search:

Type: Posts; User: Edgemoulic

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Thread: Ride Issues

    by Edgemoulic
    Replies
    20
    Views
    321

    Add up two more extra trim tabs.

    Add up two more extra trim tabs.
  2. Replies
    5
    Views
    186

    Reglarguy you have a lot of awards Hahaha! I'm...

    Reglarguy you have a lot of awards Hahaha! I'm waiting Traxxas to give you an award as well.
  3. Replies
    6
    Views
    137

    Once you get LVD, you still have 1min. To get to...

    Once you get LVD, you still have 1min. To get to shore after that 10% of power will be left
  4. Replies
    17
    Views
    310

    Minimum amp needed should be at 200amp...

    Minimum amp needed should be at 200amp recommended batteries start at 40c -5000mah up not lower than that. Check your driveline there's a possibility of binding which cause heat for the motor and...
  5. Great! Have fun and happy boating, you can charge...

    Great! Have fun and happy boating, you can charge for your service now!
  6. Replies
    9
    Views
    224

    1. NIMH is not recommended for the Spartan you...

    1. NIMH is not recommended for the Spartan you will end up using it soon.
    2. Since the props is at Center and the rudder is on the right part, the turning radius going to the left have more push...
  7. Stock Spartan turning at SLOW SPEEDS - Tuning tips?

    Water is a force, consider like swimming in the water, if your in the water you cannot run the same like when your in land, same principle with boat, with water the force is already there and trying...
  8. Replies
    7
    Views
    170

    5000mah x 30c, is not enough current, you should...

    5000mah x 30c, is not enough current, you should have 5000mahx40c min. type of batteries.
  9. 42x55 is similar to the plastic prop. The balance...

    42x55 is similar to the plastic prop. The balance will stay there forever unless you hit something which will cause your prop. To do balancing & sharpening again. Consider like changing a car tire,...
  10. If you hit something with the props, that needs...

    If you hit something with the props, that needs to check the balancing again, it will be fine for a long time.
  11. Replies
    8
    Views
    150

    Try balancing your batteries first, you will see...

    Try balancing your batteries first, you will see where's the exact voltage drop causing it.
  12. Replies
    1
    Views
    62

    Try to recalibrate it, neutral, full throttle,...

    Try to recalibrate it, neutral, full throttle, and reverse
  13. Sharpening & Balancing a Metal Propeller

    I don't really like the magnetic balancer, there is a part that the magnet was over the metal spindle which makes the balancing in-accurate, I prefer this balancer which is most accurate that had a...
  14. Kind a blurry on the image, but what I can say...

    Kind a blurry on the image, but what I can say is, tire balancers are for round type wheels, the props have a dead spot like 2 blades, after the blades it meAns that is the dead spot which a regular...
  15. Replies
    11
    Views
    194

    What batteries are you running? Hose size prefer...

    What batteries are you running? Hose size prefer is 3mm inside diameter 7mm outside diameter.
  16. Replies
    7
    Views
    170

    BTW is your props balance & sharpened?!

    BTW is your props balance & sharpened?!
  17. Replies
    7
    Views
    170

    Switched to CNC prop now overheating?

    Make a temperature check in where is the high temp. It's hard to guess without measurements, start with 5 mins. Runtime, check temp. Individually on each elects. Then additional 5 mins. Again, by...
  18. Replies
    8
    Views
    179

    Nice idea mxkid! Similar to reglarguy did, I...

    Nice idea mxkid! Similar to reglarguy did, I don't say that you copied it, everyone here have their own way of thinking, so much nicely done. Thanks for sharing
  19. Reset everything, follow the set-up tree on your...

    Reset everything, follow the set-up tree on your manual for resetting.
  20. Replies
    8
    Views
    303

    Nice vids, I wish I have that water now.

    Nice vids, I wish I have that water now.
  21. Replies
    8
    Views
    303

    Oskee as you said, you got your spartan, not a...

    Oskee as you said, you got your spartan, not a long time ago, this will be depending on the driver also, less experience less knowledge, more experience more knowledge, but it will depend on skills,...
  22. That's it, learning from each other is a big part...

    That's it, learning from each other is a big part of sharing and doing fun with the hobby as well.
  23. Replies
    11
    Views
    202

    If your doing 3s use a metal prop. since the...

    If your doing 3s use a metal prop. since the plastic prop flexes and might break.
  24. Sharpening & Balancing a Metal Propeller

    Reglarguy go on OSE here's the link
    http://www.offshoreelectrics.com/proddetail.php?prod=ose-80310
  25. Warning : Copper-beryllium can be dangerous to...

    Warning : Copper-beryllium can be dangerous to inhale. Please wear a dust mask when you are filing and sanding on your metal propeller.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4