Search:

Type: Posts; User: Brett74

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    1,761

    Seems like the HR cups with the Stainless plate...

    Seems like the HR cups with the Stainless plate are unavailable, are they discontinued?
  2. Replies
    13
    Views
    1,097

    I actually phoned my wife and got her to dig...

    I actually phoned my wife and got her to dig around and find an axle in my parts box, I didn't know but she knew how to use a Vernier and was quite insulted when I asked her if she did...she came up...
  3. Replies
    13
    Views
    1,097

    Sorry if I am being a bit thick here, I know the...

    Sorry if I am being a bit thick here, I know the axles are 6mm but the threads on the end of them are they M6 ?
    Thanks for your patience...
  4. Replies
    13
    Views
    1,097

    Not quite sure what you mean, sorry?

    Not quite sure what you mean, sorry?
  5. Replies
    13
    Views
    1,097

    No-one got a spare they can check for me ?

    No-one got a spare they can check for me ?
  6. Replies
    15
    Views
    3,566

    Actually rubber seals give better protection...

    Actually rubber seals give better protection against dirt getting in as the rubber seals better, the metal bearings offer less resistance but with all the excess power on a ERBE I didn't see that as...
  7. Replies
    13
    Views
    1,097

    Perhaps the older E-revos only had 5mm axles ?...

    Perhaps the older E-revos only had 5mm axles ? Can anyone clarify this?
  8. Replies
    13
    Views
    1,097

    Thank goodness, spent two hours making some hex...

    Thank goodness, spent two hours making some hex stabilisers thinking they were 6mm threads and then started looking around here and was sure there was some mod with a 5mm thread and some brass...
  9. Replies
    13
    Views
    1,097

    Thread size on the end of the stub axles ?

    Hey guys, out at sea at work, need to know if the threads are M6 or M5 on the axles of my ERBE ?
    Anyone care to check and let me know ?
    Thanks in advance...
  10. Thanks guys...

    Thanks guys...
  11. You guys running the Maximiser beadlocks, anyone...

    You guys running the Maximiser beadlocks, anyone running the zero offsets ? do they fit the ERBE, wooried the id of the rim might interfere with A-arm or the axle carrier...
  12. Thread: RC BEST CVD's

    by Brett74
    Replies
    25
    Views
    2,327

    I have changed my front two to the summit ones...

    I have changed my front two to the summit ones and will post on their longivety, can we use the summit center shafts too
  13. Replies
    42
    Views
    2,553

    They are fantastic, I water proofed my Esc using...

    They are fantastic, I water proofed my Esc using liquid tape but after fitting the shroud don't think it was needed. I am bashing in serious wet snow, sometimes the car just looks like a giant snow...
  14. Thread: 3.2 tires

    by Brett74
    Replies
    7
    Views
    1,397

    Promine make some masher all terrains in 3,2", I...

    Promine make some masher all terrains in 3,2", I just received a set I am going to put on rpm revolvers, just waiting for my Gorila tape tp arrive...
  15. Replies
    10
    Views
    1,917

    Can anyone else comment on what we need to fit...

    Can anyone else comment on what we need to fit the summit shafts to an ERBE, is it just the TRX 5656 long shafts and all the rest fits?
  16. Wall charger for for TX voltage and polarity?

    Thinking about putting in the NiMH batt pack in my TQi TX and was wandering about the jack on the TX, is this just a 12 volt input ? If so, what is the polarity ?
  17. Replies
    13
    Views
    1,528

    Has anyone tried the larger Gensace Hard case...

    Has anyone tried the larger Gensace Hard case packs, they now have up to 7000 mAh 2S packs availeble but it seems the sizes they give are strange, the same size or smaller than the lower mAh...
Results 1 to 17 of 17