Search:

Type: Posts; User: myst38

Search: Search took 0.01 seconds.

  1. Thread: Diff greese???

    by myst38
    Replies
    57
    Views
    5,674

    I have used 300,000k diff grease from Ofna and...

    I have used 300,000k diff grease from Ofna and then sealed the diff with rtv sealant including the screws holes.
    Been 2 months now, and not even a sign of a leak. Its a bit stiff for the first few...
  2. Replies
    19
    Views
    1,368

    I first tried the EPICS with galdiators and that...

    I first tried the EPICS with galdiators and that didn't work with VXL & 2S lipo, kept coming off the rim.
    Took the plunge and bought the switch tires thinking that would solve the problem.
    Guess...
  3. Replies
    6
    Views
    413

    The same applies for your electric. Use spit and...

    The same applies for your electric. Use spit and if it sizzles, you're way too hot. Boiling point 212F.
  4. Replies
    11
    Views
    570

    Try SPC and SMC. Both good batteries at 5000mah+...

    Try SPC and SMC. Both good batteries at 5000mah+ and 24-28C ratings.
    Around $70 - $90 depending on where you purchase them.
    get around 30 mins runtime.
  5. Thread: Where to Temp??

    by myst38
    Replies
    5
    Views
    333

    As I normally run nitro, i have 2 temp guns now....

    As I normally run nitro, i have 2 temp guns now. The PE i mentioned and now a THS tuning screwdriver bought for my losi, but these things vary greatly in temp on the VXL 15-20 degrees and only by 3-5...
  6. Replies
    12
    Views
    1,711

    If you go to www.hobbypeople.net. you will find...

    If you go to www.hobbypeople.net. you will find the castle creations with 4600kv motor on sale untill 24 March 2009 for only $119.99.
  7. Thread: Where to Temp??

    by myst38
    Replies
    5
    Views
    333

    Where to Temp??

    Where is the best place to take a temperature reading on an electric motor and why?
    I have tried on the can itself and on the endbell, with vastly different results.
    Using a VXL on 2S Lipo, but...
  8. Thread: Proper charging

    by myst38
    Replies
    15
    Views
    620

    The charge rate all depends on the battery Mah....

    The charge rate all depends on the battery Mah. Basically for more punch, you can charge at 2c, but for longer battery life and longer run times 1c is the preferred rate of charge.
    I think that...
  9. Replies
    10
    Views
    679

    I also feel that the beadlocks are a complete...

    I also feel that the beadlocks are a complete waste. VXL with 2S lipo and they usually last about 2 mins before they peel apart. Tried gladiators on them and even trimmed some of the inner thread of...
  10. Replies
    9
    Views
    571

    I wish I had found these problems before i bought...

    I wish I had found these problems before i bought the beadlocks and gladiators.
    one beadlock rim arrived with a stripped hole (brand new). The screw just keeps turning. GREAT!!!
    Also, they last...
  11. Replies
    11
    Views
    1,319

    I am using SMC 5000mah lipo and getting 30 mins...

    I am using SMC 5000mah lipo and getting 30 mins run time (stock slash) Don't use a lipo alarm or cut off either. It runs well right up to the time that the voltage drops. It runs hard all the way and...
  12. Replies
    5
    Views
    672

    Hey guys thanks for the input. Should have it...

    Hey guys thanks for the input. Should have it arriving today and going to run the stock everything against a timer, then change the ESC and see if there is a performance difference.
    I feel that I...
  13. Replies
    5
    Views
    672

    Yes, it is the stock motor. Not ready for the...

    Yes, it is the stock motor. Not ready for the brushless set up yet. Going to try stock and then think about changes after that.
  14. Replies
    5
    Views
    672

    VXL 3 and Stock Motor combo

    I have read all the forums and not come across anyone using this combo.
    I have bought the VXL-3 to run lipo as there is no good lipo cutoff available on the market.Will be running stock motor for...
Results 1 to 14 of 14