Search:

Type: Posts; User: Carlosfandango

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    246

    Thanks for the pics who is the manufacturer?

    Thanks for the pics who is the manufacturer?
  2. Replies
    6
    Views
    640

    Shame as there's lots of plastic parts that could...

    Shame as there's lots of plastic parts that could do with that FLM touch.
  3. Replies
    5
    Views
    246

    Replacement upgraded Servo saver

    I hope someone can help, I'm after an uprated steering servo for my FLM Emaxx the hot racing one has given up the ghost and I was hoping to find an unlimited engineering one but I've emailed UE for...
  4. Brilliant I will work on this tomorrow i take it...

    Brilliant I will work on this tomorrow i take it the crown wheel inside the diff housing just pulls off?
  5. How do I do this? I've taken the bulkhead apart...

    How do I do this? I've taken the bulkhead apart and there's no grub screws to remove the drive cups how do I do this I can't send pictures on here for some reason
  6. Hi guys the 7TQ differentials arrived and they do...

    Hi guys the 7TQ differentials arrived and they do slot in but they have a bigger output shaft I can't seem to attach a yoke do I need to get 7TQ yoke and I can't post pictures on here for some reason...
  7. Thanks for that just ordered a set not bad 35...

    Thanks for that just ordered a set not bad 35 incl postage so I'll bin the stainless steel replacements.
  8. Thanks everyone I'll be servicing the...

    Thanks everyone I'll be servicing the differentials at the weekend and just checking all is ok they seem to be fine turning smooth as silk just the cups are shot gives me a chance to replace the...
  9. Thank you so much I've had 2 years of good...

    Thank you so much I've had 2 years of good bashing this is the first problem and totally my fault lol
  10. The longer ones I know are revo stubs but the...

    The longer ones I know are revo stubs but the ones in the middle where can I get them?
  11. Ahhhhh it's the drive cups that have broken can I...

    Ahhhhh it's the drive cups that have broken can I just swap them out for revo 513R ones?
  12. No they are the dog bone ones not the splined ones

    No they are the dog bone ones not the splined ones
  13. Hi there for some reason I can't attach pictures...

    Hi there for some reason I can't attach pictures but if you look at the hybrid bulkhead with the pinion yoke facing towards you the left drive cup that goes into the MIP CV shaft and joint dogbone is...
  14. What can I do to repair my FLM differentials

    After 2 years of running my FLM chassis and hybrid bulletproof diffs I decided to install a Robinson racing slipper clutch didn't back it off enough and with 5 minutes broke both the front and rear...
  15. Ordered some erevo axle carriers from the US...

    Ordered some erevo axle carriers from the US hopefully they will have the metal rings.
  16. With regards the rings I've got two sets of new...

    With regards the rings I've got two sets of new 533R carriers and they don't have these rings to pop off...... Any ideas were I can get them?
  17. I've found two potentials and will keep my...

    I've found two potentials and will keep my fingers crossed they have stock
  18. Hi there yes I couldn't get the inner in anymore...

    Hi there yes I couldn't get the inner in anymore if I tried, just such a pain as the atomik ones look great, but I've ordered a pair of STRC with oversized bearings, however I spotted a German site...
  19. Well I took out my dremmel and ground down the...

    Well I took out my dremmel and ground down the raised part of the hex hub it made a difference but not enough, so I kept grinding and eventually I could get the pin through but not far into the hex...
  20. Will be trying that tomorrow if they don't work...

    Will be trying that tomorrow if they don't work I'm ordering the STRC knuckles and the fancy German 17mm hubs :-)
  21. I spotted Hot Racing ones and GPM ones so, all I...

    I spotted Hot Racing ones and GPM ones so, all I can find are Atomik I have these and they don't work with the excellent MIP CVDs, so that leaves STRC, HotRacing and GPM......

    Yes it does I'll try...
  22. Hi there I've been trying to find the Teckno ones...

    Hi there I've been trying to find the Teckno ones with no luck emailed Teckno no reply.... Yes I'm using the blue ones, STRC look like they've had positive reviews but I'm hanging on to find Teckno...
  23. MIP CVD what alloy knuckles will they work with

    I posted this in the Emaxx section but I have a mamba 2 powered brushless FLM with MIP CVDs into Rpm arms however I need to beef the fronts up so bought in a recommendation the atomik ones, they...
  24. Alloy axle carriers that work with MIP CVD for Emaxx problems with Atomik ones

    I have an FLM emaxx brushless that has gone through numerous RPM front knuckles and I'm tired of the pillow balls pushing through after a tap here and there. I bought a set of atomik knuckles but the...
  25. Replies
    2
    Views
    443

    E Maxx axle carriers alloy or not

    Hi there I have a castle mamba powered, fully FLM chassis ultimate hybrid bulks, MLP Cvs and Drive shafts, RPM arms and axle carriers HiTec titanium geared servo, after a high speed run and hitting a...
Results 1 to 25 of 59
Page 1 of 3 1 2 3