Search:

Type: Posts; User: Corex2

Page 1 of 19 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    322

    "honey have you seen my favorite makeup brush ?"

    "honey have you seen my favorite makeup brush ?"
  2. Replies
    10
    Views
    556

    nice. that will look sharp. one of the best parts...

    nice. that will look sharp. one of the best parts of the slash 4x4 is the versatility of having a choice in your hopups a lot of other vehicles let you upgrade a part, but there's not a style or...
  3. Replies
    27
    Views
    585

    your original request was 2s.. before you think...

    your original request was 2s.. before you think about making a 3s/2200kv motor jump you'll need to upgrade your drive line, but this combo is a favorite here.
  4. Replies
    27
    Views
    585

    what conditions do you run in, grass, dirt,...

    what conditions do you run in, grass, dirt, pavement ... ? have you tried gearing down a tooth or two and putting a fan on the esc, 2s really shouldn't be that big of a problem on the vxl, except if...
  5. Replies
    10
    Views
    556

    no bending. i popped one rear shaft with a set of...

    no bending. i popped one rear shaft with a set of arms that were beat on for about 2 years. replaced them since they were pretty trashed anyway and i haven't popped another. next time i rebuild my...
  6. Replies
    10
    Views
    556

    are you planning on upgrading your drive shafts ?...

    are you planning on upgrading your drive shafts ? if you are teknos come with the rear and front carrier of their own so that would leave you with just the c-hubs. i have them with rpm arms and...
  7. Replies
    19
    Views
    837

    RPM makes nerf bars for the LCG chassis too,...

    RPM makes nerf bars for the LCG chassis too, maybe another supplier in your area or someone with international shipping. they're beefy and pretty sweet looking....
  8. Replies
    30
    Views
    1,302

    i'm not a fan of the battery hold down on the lcg...

    i'm not a fan of the battery hold down on the lcg chassis, without velcro or other mods, it's just not very fail safe, i'd like to see a more secure battery strap that can take a wider range of...
  9. Replies
    4
    Views
    283

    i'd drop to like 15/54 and check temperatures...

    i'd drop to like 15/54 and check temperatures there, maybe put a fan of the esc. the failure of your suspension to bounce back will be enhanced with thicker oil since that will create more dampening....
  10. Replies
    4
    Views
    283

    5k wouldn't be enough to act like a locked diff....

    5k wouldn't be enough to act like a locked diff.

    i'd start with slaydens set up and go from there. it's a solid base point to modify from and you always have a good reference point. i'd also look...
  11. check the bearing adapter on your slipper. if...

    check the bearing adapter on your slipper. if it's the stock plastic one it might be badly worn.
  12. Thread: Steering issue

    by Corex2
    Replies
    17
    Views
    380

    you can get a copy of the manual for your radio...

    you can get a copy of the manual for your radio online to learn how to set the endpoints and trim.
  13. Thread: Steering issue

    by Corex2
    Replies
    17
    Views
    380

    it sounds like your trim is set all the way to...

    it sounds like your trim is set all the way to the left.

    you installed the new servo correctly ?

    set your trim to zero
    power up the servo
    install the horn at 1 o'clock-ish (for lcg chassis)...
  14. i don't like the top end of it and it didn't have...

    i don't like the top end of it and it didn't have enough torque for me. i THINK it's officially considered a 550, but i'd say it preforms more like a 540. i've settled into 2 3500s now, i'm happy...
  15. you won't have to modify the chassis for either...

    you won't have to modify the chassis for either of them. you'll need to get a motor mounting plate with the sidewinder and maybe have ends soldered on to match your batteries, same with the hobbywing...
  16. i'd say go stock and gear down a bit if you're...

    i'd say go stock and gear down a bit if you're THAT concerned. there's plenty of people running the stock truck that don't have any issues. pick yourself up a temperature gauge to monitor your motor...
  17. Replies
    8
    Views
    389

    add a dap of glue to the threads on those pins as...

    add a dap of glue to the threads on those pins as well, they notoriously back out.
  18. Replies
    8
    Views
    389

    even on their own blocks the pin does not extend...

    even on their own blocks the pin does not extend all the way through.
    http://traxxas.com/sites/default/files/6832X-aluminum-C-hub_6804L-6807L.jpg
    (i THINK this is what you're referring to)

    i...
  19. Replies
    13
    Views
    293

    you can limit your travel by adjusting the...

    you can limit your travel by adjusting the mounting location of your shock. or limiters (small spacers) can be installed on the shock shaft under the piston (fuel line tubing 2 or 3 mm pieces works...
  20. Replies
    4
    Views
    333

    same thing really, reduce the size of the pinion...

    same thing really, reduce the size of the pinion or increase the size of the spur would both be "gearing down"
  21. Replies
    5
    Views
    546

    i'm an Avid bearing fan. i think buying a kit...

    i'm an Avid bearing fan. i think buying a kit from ebay you'd be more likely to find they're not what they claim to be. try avids or boccas, most people here will agree, and at a buck a piece they're...
  22. Replies
    10
    Views
    366

    from amain......

    from amain...
    http://www.amain.com/Pro-Line-Extended-Front-Rear-Body-Mounts-Slash-4x4/p237048
  23. Replies
    10
    Views
    366

    depends on your definition of "bigger". to get...

    depends on your definition of "bigger". to get the most lift flexibility the proline body mounts will give you much more clearance.
  24. Thread: New esc

    by Corex2
    Replies
    5
    Views
    200

    sure it would be, you'd just need to make sure...

    sure it would be, you'd just need to make sure you used the same size bullet connectors.
  25. sweet ride badaml. things get a little tricky...

    sweet ride badaml. things get a little tricky using speed controllers bigger than the MMP since you're using the VG chassis brace. i made a lexan esc plate receiver box offset for my trucks and i can...
Results 1 to 25 of 472
Page 1 of 19 1 2 3 4