Search:

Type: Posts; User: TheGuy

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    297

    The motor I am running is the Venom 8.5t which is...

    The motor I am running is the Venom 8.5t which is 5200kv. I want to be able to drive on the street and offroad as well.

    Also I have 2 different lipo packs, one 2s 30c 5000mah and one 3s 30c 5000mah
  2. Replies
    5
    Views
    297

    BL Gearing Question

    What would be a good gearing on a 5200kv setup? Was curious what kv the VXL motor is.
  3. Thread: Revo Question

    by TheGuy
    Replies
    5
    Views
    298

    I would buy it all right now for 350

    I would buy it all right now for 350
  4. Replies
    4
    Views
    249

    A 3000mah sport pack will do just fine. Check out...

    A 3000mah sport pack will do just fine. Check out your LHS they prolly have something that will fit the bill for around 20-25$
  5. Replies
    17
    Views
    680

    ^ Looks nice, but a nice piece of lightweight...

    ^ Looks nice, but a nice piece of lightweight alumn. is pricey, plus the proper tools to cut and drill it.
  6. Replies
    15
    Views
    3,354

    Across the spectrum everyone had problems with...

    Across the spectrum everyone had problems with these motors holding a good tune. There were the few who swore up and down by them but now a days you hardly see them, O.S. has been the top dog in...
  7. Replies
    9
    Views
    368

    Replace the stock a arms with RPM ones when he...

    Replace the stock a arms with RPM ones when he breaks the stock ones. Not much else I can think of you would need right away other than some extra glow plugs. Depending on the model you buy you might...
  8. Replies
    10
    Views
    694

    the internets

    the internets
  9. Replies
    9
    Views
    368

    Revo.. I have owned them all and the revo is a...

    Revo.. I have owned them all and the revo is a good truck. Its a sturdy truck. If you wanted to get him into nitro without the big bucks you could also look at the nitro stampede which is lots of fun...
  10. Replies
    13
    Views
    3,320

    Can you guys compare a chevy 4x4 vs a ford 4x4......

    Can you guys compare a chevy 4x4 vs a ford 4x4...

    Give me a break. Your going to get a hundred opinions either way. The revo and the savage are not the same kind of machine. But based on your...
  11. Replies
    1
    Views
    849

    Tower checkout code?

    Anyone have a discount code for tower thats current?
  12. Replies
    18
    Views
    704

    Servo spoken for. 3.3 back up for grabs after...

    Servo spoken for. 3.3 back up for grabs after buyer flaked. 3.3 not 50% off :rolleyes:
  13. Replies
    9
    Views
    531

    Yeah I have had an aluminum one in the past and...

    Yeah I have had an aluminum one in the past and hit a half buried cinder block and it caused all kinds of problems. So looking to replace the one on the truck.
  14. Replies
    18
    Views
    704

    Its Thanksgiving... 50% off everything. Last...

    Its Thanksgiving... 50% off everything. Last chance
  15. Replies
    8
    Views
    658

    If its a 23mm wheel yes

    If its a 23mm wheel yes
  16. Replies
    22
    Views
    3,410

    I have two FLM sealed diffs.. both holding up...

    I have two FLM sealed diffs.. both holding up well on a 6200kv bl with 3s lipo. The screws included work fine, and no shimming required. Recheck and rebuild the diff and see what you think when you...
  17. Replies
    14
    Views
    2,119

    I dont see how you guys are breaking the mip...

    I dont see how you guys are breaking the mip cvd's. Must be your driving, because I have used cvd's on most of my rc's for years without any problems and if I did it was due to my driving faults.
  18. Replies
    76
    Views
    5,153

    Never could understand why you would want to make...

    Never could understand why you would want to make an all aluminum truck. I would rather that someone like RPM make an all plastic conversion but replacing all parts including the chassis.
  19. Replies
    9
    Views
    531

    Front Skid Plate

    Does anyone make a good front skid plate? I just got a 2nd hand revo and it has a blue anodized aluminum. I prefer plastic to aluminum especially for the front skid. Was curious if anyone makes...
  20. Replies
    8
    Views
    417

    Looks good. Wonder if it will be up to par with...

    Looks good. Wonder if it will be up to par with RPM. Too bad RPM doesnt make a wider variety of parts.
  21. Replies
    9
    Views
    379

    +2 Junk & waste of money. Integy has good...

    +2 Junk & waste of money. Integy has good intentions but the quality of parts never last.
  22. Replies
    7
    Views
    304

    +1 I found other good uses for (pony tail) rubber...

    +1 I found other good uses for (pony tail) rubber bands as well. Lol'd as I read it because I use them all the time. My girls get :mad: when I take them
  23. Thread: new revo

    by TheGuy
    Replies
    7
    Views
    426

    Dont think you have the right idea. If your on...

    Dont think you have the right idea. If your on the prowl to buy a used revo just keep searching the "MARKET PLACE" here or on other forums and pm potential sellers. You will get better results that...
  24. Replies
    3
    Views
    280

    A lil wd40 and a toothbrush and all those parts...

    A lil wd40 and a toothbrush and all those parts would be clean ;)
  25. Replies
    36
    Views
    3,802

    Looks good. Cant wait to see it in a video. If...

    Looks good. Cant wait to see it in a video. If you do go brushless get a moderate kv motor and you will have tons of fun.
Results 1 to 25 of 348
Page 1 of 14 1 2 3 4