Search:

Type: Posts; User: Low Yi Dah

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    304

    LCG chassis durability

    Wondering how the current LCG chassis that come with the LCG slash 4x4 hold up. Do they break easily? I remembered reading about them breaking at the front a while ago but not sure if they have...
  2. Replies
    4
    Views
    223

    Could it have to do with the potentiometer?

    Could it have to do with the potentiometer?
  3. Replies
    4
    Views
    223

    The servo wire does not stick out from the top,...

    The servo wire does not stick out from the top, rather the side. So would be impossible to just simply push it in. Had to take apart the bottom half and install first than the top half on top.
  4. Replies
    4
    Views
    223

    Servo problem

    Hi guys, just got a corona ds238mg servo. Opened it up so that I could install it on my erevo vxl. Some gears fell out and I put them back. However, after that, the servo could not centre and kept...
  5. Replies
    5
    Views
    229

    HUh? I think you mixed me up with somebody else....

    HUh? I think you mixed me up with somebody else. I did not even pm you! And this is just my second thread about servos.
  6. Replies
    5
    Views
    229

    Dont like the stock servo as it strips and burns...

    Dont like the stock servo as it strips and burns way too often
  7. Replies
    5
    Views
    229

    Waterproofing servo

    I want to waterproof a servo for my MERV. Would putting duct tape around the gaps and grease along the spline do the job? Thanks in advance:)
  8. Thread: Servo

    by Low Yi Dah
    Replies
    3
    Views
    286

    The site says that operating travel is 40...

    The site says that operating travel is 40 degrees, is that fine?

    It is 33mmx34mmx17mm, will it fit well without modification
  9. Thread: Servo

    by Low Yi Dah
    Replies
    3
    Views
    286

    Servo

    Any experience with the corona DS339HV servo, or any corona servo? Does it work with the older traxxas 2.4ghz TQ radio?
  10. Replies
    12
    Views
    629

    Will try to see if the same happens with the...

    Will try to see if the same happens with the servo without the horn.
  11. Replies
    12
    Views
    629

    Does endpoint adjustment solve the heat and...

    Does endpoint adjustment solve the heat and chatter? When turning to left, the servo jerks bit by bit, vibrating along the way, and I can turn it by hand without having much resistance. This is not...
  12. Replies
    12
    Views
    629

    By the way, the stock servo did not have the same...

    By the way, the stock servo did not have the same problem.
  13. Replies
    12
    Views
    629

    Hitec 82mg problems?

    I just got a hitec 82mg servo for my merv. When Turing right, it is fine. But turning left, even centering from right, would cause severe heat and chatter. At times, it can't even turn left. Any...
  14. Replies
    1
    Views
    200

    MERV very slow after driving in rain

    After driving the MERV in some fairly heavy rain, it moves at only 3mph at full throttle. Receiver and transmitter, as well as battery and servo still work. Motor seems fine ad it works with another...
  15. Replies
    4
    Views
    389

    Spring removal

    Hi guys, been trying to remove the spring from the shock. However, I just can't seem to remove the spring retainer. Any suggestions?
    Thanks!
  16. Replies
    9
    Views
    1,205

    Where can I buy that tool?

    Where can I buy that tool?
  17. Replies
    9
    Views
    1,205

    Strange. I have 2 MERVs and yet to find that U...

    Strange. I have 2 MERVs and yet to find that U joint
    tool.
  18. Replies
    9
    Views
    1,205

    How come a U joint can rub against a bulkhead? By...

    How come a U joint can rub against a bulkhead? By the way, I was talking about the joint which is a ball with 4 things sticking out forming a t shape.
  19. Replies
    9
    Views
    1,205

    Rustler U joints

    I just got some rustler U joints to replace those of a MERV as they keep popping out. However, due to the longer pin length, I'm having a real problem putting the rustler U joints in. Also having a...
  20. Replies
    1
    Views
    214

    Popping in/out U joints?

    My MERV's driveshafts have been popping out every 5 minutes. So I have gotten rustler U joints to solve the problem(rustler U joints have longer pins but ball has the same diameter). Does anyone know...
  21. Thread: 7151x???

    by Low Yi Dah
    Replies
    23
    Views
    1,333

    7151x???

    Been searching all over the place but I can't find the Traxxas 7151x steel driveshafts. Tower Hobbies ran out of stock so now I do not know where else I can get it. Where can I get the 7151x? Thanks...
  22. Why mamba monster and not waterproof???

    Why did Traxxas decide to use the Mamba Monster instead of the Tekin Rx8? They both seem like very good brushless systems. And why did they not bother to waterproof the Mamba Monster while...
  23. Don't try Barnfloor. Heard that some people have...

    Don't try Barnfloor. Heard that some people have problems with them. Poor quality control, selling your personal information, etc. type in: Barnfloor rc review on google and see for yourself.
  24. Replies
    40
    Views
    930

    Very true,I agree with you 100%

    Very true,I agree with you 100%
  25. Replies
    40
    Views
    930

    What petertje60 have said is true to some extend...

    What petertje60 have said is true to some extend but some parts just have to be upgraded as they keep popping out or breaking.If you dont upgrade them,woulnt it cause more time,money and...
Results 1 to 25 of 71
Page 1 of 3 1 2 3