Search:

Type: Posts; User: akadi

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    726

    Just to make..the positive is the solid wire? On...

    Just to make..the positive is the solid wire? On both the receiver battery charger and the ez start battery charger?
  2. Replies
    3
    Views
    726

    Receiver Battery Charger

    Hi,
    Its been a while since I posted here, as I was a bit busy and hardly using my revo. I just pulled it out today and I noticed that the wires of the receiver charger is snatched from the...
  3. Replies
    17
    Views
    883

    the servos should act the same wether the engine...

    the servos should act the same wether the engine is running or not. remove the air filter and turn the radio on, look inside the carb and see how the carb slider behaves when you press/release the...
  4. Thread: engine temp

    by akadi
    Replies
    18
    Views
    888

    Factory setting for HS & LS needles CAN be too...

    Factory setting for HS & LS needles CAN be too lean. Look for other signs than just temp (smoke, performance) to decide wether they are lean or not. Always start with 1mm idle gap (and never...
  5. Thread: DIY Setup System

    by akadi
    Replies
    15
    Views
    4,701

    search for "set up board decals"

    search for "set up board decals"
  6. Replies
    3
    Views
    948

    Kadi's Revo Upgrades & Questions

    Hi guys..thought I'd share with you my newest revo add on..the OS .21TM

    http://i1093.photobucket.com/albums/i430/akadi/Revo/truck.jpg

    I am currently running it with 16/36 gear. I am still...
  7. Thread: DIY Setup System

    by akadi
    Replies
    15
    Views
    4,701

    very nice work man..i ve always contemplated...

    very nice work man..i ve always contemplated creating something similar. not sure if you are aware of this, but there are some ready made setup declass with the all he measurements. you can get for...
  8. Replies
    5
    Views
    1,963

    but with the ez start attached, shouldn't the one...

    but with the ez start attached, shouldn't the one way bearing stops it from rotating clockwise?
  9. Replies
    5
    Views
    1,963

    FLywheel Rotation Direction

    Hi..i am just wondering if you should be able to rotate your fly wheel clockwise? is there something wrong if it does? thanks
  10. Thread: Flywheel Nut

    by akadi
    Replies
    17
    Views
    1,487

    i got the blue flywheel and i didn't wanna scroe...

    i got the blue flywheel and i didn't wanna scroe it. the wrench just seemed neat. bargain at that price too.
  11. Thread: Flywheel Nut

    by akadi
    Replies
    17
    Views
    1,487

    oh i see. thanks for the heads up. I thought it...

    oh i see. thanks for the heads up. I thought it was the safest way to get the nut out. I saw a tool that locks the piston, but though this was less invasive.
  12. Thread: Merry X-Mas

    by akadi
    Replies
    7
    Views
    660

    Merry X-Mas

    Just wanna take this opportunity to wish everyone here a merry x-mas and a happy new year. You guys have amazing to say the the least. Thank you all for your help(s)!

    Cheers
  13. Thread: Flywheel Nut

    by akadi
    Replies
    17
    Views
    1,487

    sorry i don't get it, how can you loosen the...

    sorry i don't get it, how can you loosen the clutch pins with this wrench? Doesn't it just grabs on the pins to secure the wheel in place?
  14. Thread: Flywheel Nut

    by akadi
    Replies
    17
    Views
    1,487

    nothing fancy really, i got one real cheap for $6...

    nothing fancy really, i got one real cheap for $6


    still waiting for everything to arrive thou
  15. Thread: Flywheel Nut

    by akadi
    Replies
    17
    Views
    1,487

    no need for the rag and channel lock, i got a fly...

    no need for the rag and channel lock, i got a fly wrench. thanks
  16. Thread: Flywheel Nut

    by akadi
    Replies
    17
    Views
    1,487

    Flywheel Nut

    Hi guys,

    How tight do you tighten the flywheel nut? i read some where it should be over tightened and loctited. Other said that that could damage the crank shaft and it should be just snug. ...
  17. Replies
    4
    Views
    558

    Well apparently not everything. I still can't log...

    Well apparently not everything. I still can't log on from any web based browser or computer. Only tapatalk for now
  18. Replies
    4
    Views
    558

    What's Wrong With The Forum?

    Hi, I ve been have tremendous difficulties recently getting into the forum website. For 5 days it gave me a database error. And now I can display the posts, but when I try to log in to start or...
  19. Replies
    19
    Views
    1,728

    the opti drive also has a low voltage fail safe. ...

    the opti drive also has a low voltage fail safe. it monitors the receiver battery, and warns you when its voltage has dropped. so with the optidrive out, you should be careful to keep rx battery...
  20. Replies
    19
    Views
    1,728

    if you by pass the optidrive, one thing i found...

    if you by pass the optidrive, one thing i found very useful is to lock the reverse so you don't hit it accidentally. if you look carefully on the top of reverse button on the transmitter, you will...
  21. Replies
    39
    Views
    3,944

    thank yo jake

    thank yo jake
  22. Thread: Sealer

    by akadi
    Replies
    5
    Views
    838

    there is one i heard was good, never used it...

    there is one i heard was good, never used it thou, Lucky 7. Best thing about it is that you apply it externally .
  23. Replies
    10
    Views
    910

    LOL@Jake DG, I asked him first if he was...

    LOL@Jake


    DG, I asked him first if he was lubecakes from traxxas, and he said no, he dosnt come here anymore :D

    http://www.rcnitrotalk.com/forum/showthread.php?p=909937#post909937
  24. Replies
    10
    Views
    910

    lubes, check this ...

    lubes, check this

    http://www.rcnitrotalk.com/forum/showthread.php?t=45678&page=37

    this guy 2revo1maxx has your fotos and saying that the trucks are his!!!
  25. Thread: breaking in time

    by akadi
    Replies
    17
    Views
    635

    about an hour and half, including the cool down...

    about an hour and half, including the cool down time of the first 2 tanks
Results 1 to 25 of 272
Page 1 of 11 1 2 3 4