Search:

Type: Posts; User: Rx7_Dez

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    516

    Yea nice job. I have just taken the heat sink off...

    Yea nice job. I have just taken the heat sink off and seen where the problem came from, you can see it was wet and had loads of sand in between the chips and shorted there. Did you seal yours between...
  2. Replies
    7
    Views
    516

    Yea by looking at the price difference it might...

    Yea by looking at the price difference it might be best to get the v3 and just do it myself. What was the name of the silicone you use to seal it?

    Cheers again
    Dez
  3. Replies
    7
    Views
    516

    Ok but the only thing is I'm in Spain so I guess...

    Ok but the only thing is I'm in Spain so I guess I would have to send them in old one to get a flat repair so it won't be worth it.

    Might as well go for the waterproof one while I'm at it.
    ...
  4. Replies
    7
    Views
    516

    Mamba Monster esc v3 smoking solenoid.

    Hi all,

    I was out with the truck yesterday and there was a small puddle that the truck went through a couple of times but all was ok until batteries ran out. When i went to turn of the truck the...
  5. Replies
    4
    Views
    388

    Ok Cheers mate, I just realised that I didn't...

    Ok Cheers mate, I just realised that I didn't post in emaxx brushless thread either. Will post it there too just in case before I buy a new one.
  6. Replies
    4
    Views
    388

    Its a Mamba Monster V3. Cant believe from a tiny...

    Its a Mamba Monster V3. Cant believe from a tiny little bit of wet sand its fried the esc. Probably has though, but cant it be fixed? Or is it just cheaper to replace?

    Cheers
  7. Replies
    4
    Views
    388

    Castle Esc problems

    Hi all,

    I was out with the truck yesterday and there was a small puddle that the truck went through a couple of times but all was ok until batteries ran out. When i went to turn of the truck the...
  8. Replies
    0
    Views
    201

    Extra long chassis

    I am looking to get a aluminum chassis but I would like to know if anyone knows if there are any longer chassis than the flm or gorillamaxx chassis, the stock chassis is 335mm I am looking to see if...
  9. Replies
    177
    Views
    29,252

    ahhh no way, even if I am running the flm towers?...

    ahhh no way, even if I am running the flm towers? Would you know how much longer they are?
  10. Replies
    177
    Views
    29,252

    Hey Ben, I am bidding on some losi 8 shocks but I...

    Hey Ben, I am bidding on some losi 8 shocks but I have just realized that 1 set is losi 8 2.0 rear shocks (green springs) and the other set are losi 8 2.0 truggy big bore shocks (grey springs), are...
  11. Replies
    177
    Views
    29,252

    Hey Ben, I have read over you installing the losi...

    Hey Ben, I have read over you installing the losi shocks, and I just wanted to confirm something if I am still running the stock drive shafts and I want to install 1 losi shock per side will I have...
  12. Replies
    17
    Views
    287

    Waterproof?? Have you got the 3908, brushless...

    Waterproof?? Have you got the 3908, brushless edition? If so then they are not waterproof, and I would try to stay away from all water unless you want to plastic dip your esc.
  13. Replies
    177
    Views
    29,252

    I am running 5s at the moment, just awaiting some...

    I am running 5s at the moment, just awaiting some quotes for the geode´s and badlands so hopefully order them soon. Also your truck looks really wide have you done anything to widen it up even more,...
  14. Replies
    17
    Views
    287

    Hi Redsawacs, you have already got 2 guru´s...

    Hi Redsawacs, you have already got 2 guru´s helping you out, but I just had a very similar problem so I would like to add a bit of info. I had the same problem when i braked hard i got a metal...
  15. Replies
    177
    Views
    29,252

    Yes I saw that Thesnakejake had the same issue...

    Yes I saw that Thesnakejake had the same issue (link below) although other people had made it fit with a spoiler and it looks awesome. I am not going to use a spoiler so I should be ok, I just hope...
  16. Replies
    177
    Views
    29,252

    Hi Ben, just a quick question I liked the look of...

    Hi Ben, just a quick question I liked the look of yours and 87_gn geode´s with badlands, so I have been just looking up to buy some but I see in a later photo of yours that you have a beadlock red...
  17. Replies
    18
    Views
    1,478

    Yea well its back and running again, it was just...

    Yea well its back and running again, it was just the inner bearing like you said, I have replaced it with a bearing that I had on some spare axle carriers I had, the teeth on the bar that was inside...
  18. Replies
    18
    Views
    1,478

    Yea well found out by trial and error it was the...

    Yea well found out by trial and error it was the front diff which is now totally shot! I have found there are a couple of aluminium ones on ebay for around 14$ but they are off a t-maxx 3.3, would...
  19. Replies
    18
    Views
    1,478

    Hi Ben, yea that is the part I have just ordered,...

    Hi Ben, yea that is the part I have just ordered, the output shaft, from what Mayhem mentioned i have realized that the slipper clutch was hardly working at all. When I ran the truck on tarmac for...
  20. Replies
    18
    Views
    1,478

    Cheers Mayhem, I just ordered the stock gear and...

    Cheers Mayhem, I just ordered the stock gear and I couldn't find the avid bearings in the sizes I needed, and the Acer bearing cost quite a bit and then double again just to post them. As my bearings...
  21. Replies
    18
    Views
    1,478

    Yea that will be it for sure, although I bought...

    Yea that will be it for sure, although I bought the truck second hand although the old owner only had it for two months, he must of tightened up the clutch too much. I am about to order the 3984X...
  22. Replies
    18
    Views
    1,478

    The noise that I have seems to be coming from the...

    The noise that I have seems to be coming from the transmission, if I turn the wheels with pinon not connected to the spur I can hear a noise, it is only a faint noise but it is the same noise when...
  23. Replies
    18
    Views
    1,478

    Hi Mayhem, yes I do but they all seem ok. And...

    Hi Mayhem, yes I do but they all seem ok. And when I spin the with my hand they dont make any noise. Why what could it be?? I have just checked the pinion and spur and no missing teeth. It is the...
  24. Replies
    18
    Views
    1,478

    Clicking noise when braking

    I took the truck out today after installing the mamba motor far and upgrading the shock oil to 60wt (which made a big difference btw), I was driving on tarmac which I don't usually do and when i put...
  25. Replies
    7
    Views
    313

    Went out today with Sky lipo 3s, 5000mah, 40c and...

    Went out today with Sky lipo 3s, 5000mah, 40c and Sky lipo 2s, 5000mah, 40c and all I can say is woooooooooooow!! What a difference, now this is what I call fun!! Managed to lose a centre drive screw...
Results 1 to 25 of 75
Page 1 of 3 1 2 3