Search:

Type: Posts; User: gorilla2891

Page 1 of 15 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    13
    Views
    159

    Yes, but it is for 2 nimh in series on flat hard...

    Yes, but it is for 2 nimh in series on flat hard surfaces the extra voltage gets you to 55+ the smaller gear helps take load off electrics. You can get 50 with stock gearing on 3s lipo.
  2. Replies
    1
    Views
    11

    ? pic? Pillow ball adjustment is out or something...

    ? pic? Pillow ball adjustment is out or something is broken...
  3. Replies
    13
    Views
    159

    3s is fine for the merve. It is the "speed"...

    3s is fine for the merve. It is the "speed" pinion that is only for pavement and flat surfaces...
  4. Replies
    13
    Views
    159

    I ran stock esc and gearing for years on 3s in...

    I ran stock esc and gearing for years on 3s in Charleston heat, with a heatsink/fan on motor. It is a good thing no matter what you do.
  5. I tried a center diff, i did not like it.... Your...

    I tried a center diff, i did not like it.... Your problem, pre center diff sounds like slipper adj, and, or rear diff losing fluid. You should pull, check, refill with 30wt, rtv mating surfaces and...
  6. Replies
    9
    Views
    119

    You will hear w whining noise from the slipper...

    You will hear w whining noise from the slipper when worn out when you hit the gas..
  7. Replies
    7
    Views
    428

    Front 50wt traxxas rear 30wt. But clean diffs and...

    Front 50wt traxxas rear 30wt. But clean diffs and seal mating surfaces and screw holes with rtv. otherwise diff fluid will leak out and no limited slip.... = spinouts when throttle is hit
  8. Replies
    7
    Views
    428

    Center diff is not needed. Proper oils in diffs...

    Center diff is not needed. Proper oils in diffs is better
  9. Use the centerdiff and adjust the slipper. You...

    Use the centerdiff and adjust the slipper. You can keep the 4wd. 50k front and center, 30k rear?
  10. Replies
    20
    Views
    528

    Well, when one of those get bent you can... :)

    Well, when one of those get bent you can... :)
  11. Replies
    20
    Views
    528

    get the summit rear arms, 10mm extended and...

    get the summit rear arms, 10mm extended and Booyah!

    Side note, better handling...
  12. Replies
    53
    Views
    6,746

    WOW! Hobby room....:p~ what's in that fridge?...

    WOW! Hobby room....:p~

    what's in that fridge? :thumbup:
  13. Thread: $16

    by gorilla2891
    Replies
    9
    Views
    291

    Heatsink/fan for motor is a good investment.

    Heatsink/fan for motor is a good investment.
  14. Replies
    2
    Views
    74

    Traxxas wheelie bar? Remove rear bulkhead braces...

    Traxxas wheelie bar? Remove rear bulkhead braces and bolt in.. ? I have T bone set up so its been a while......
  15. Replies
    11
    Views
    387

    AWESOME! :thumbup:

    AWESOME! :thumbup:
  16. If you do not want ballooning, you have to buy...

    If you do not want ballooning, you have to buy tires and wheels separately. And tape the inside of tires with gorilla tape, before gluing.
  17. Not wider, lengthens wheelbase. I love my...

    Not wider, lengthens wheelbase. I love my trenchers! But I cannot use on pavement. Traction roll city. They are awesome everywhere else.And I do have my car sorted out...

    What squeegie said...
  18. I tried the spacers, they were a little too loose...

    I tried the spacers, they were a little too loose for my liking. Wider wheels and summit 10mm extended rear arms have the best effect on handling
  19. Replies
    1
    Views
    102

    Steel cvds are way stronger. When you upgrade it...

    Steel cvds are way stronger. When you upgrade it is needed. Blew out a plastic stock one. Keep your pillow balls tight and the should stay in.
  20. Thread: 3s no go

    by gorilla2891
    Replies
    7
    Views
    166

    Sounds like a loose connection...

    Sounds like a loose connection...
  21. Replies
    8
    Views
    172

    Cut only the door. Cutting the chassis weakens...

    Cut only the door. Cutting the chassis weakens its. Doors are cheap..
    http://i887.photobucket.com/albums/ac74/gorilla2891/Mobile%20Uploads/0115151932_zpsed3192fa.jpg
  22. Replies
    5
    Views
    247

    Hot racing makes them, but seem unavailable right...

    Hot racing makes them, but seem unavailable right now.
  23. Thread: Oba?

    by gorilla2891
    Replies
    4
    Views
    146

    I've pondered the idea. It would be cool.

    I've pondered the idea. It would be cool.
  24. traxxas wheelie bars help... when burst is hit

    traxxas wheelie bars help... when burst is hit
  25. disconnect servo and try. Bad servos are very...

    disconnect servo and try. Bad servos are very common issue. They often cause this, as well as frying esc.
Results 1 to 25 of 365
Page 1 of 15 1 2 3 4