Search:

Type: Posts; User: ROB311952

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    19
    Views
    443

    That means the throttle trim isn't set right or...

    That means the throttle trim isn't set right or you weren't quick enough on your releases. Go through the trim process in the back of the manual, then try reprogramming your esc. If you can't get it...
  2. Replies
    22
    Views
    504

    I run 19/86 for bashing and short oval track. ...

    I run 19/86 for bashing and short oval track. This runs nice and cool on 2S and gives very good acceleration and wheelies.
  3. Replies
    6
    Views
    347

    Bad. Plastic gears are cheap and last a long time...

    Bad. Plastic gears are cheap and last a long time if you set the mesh correctly. If you make that part stronger (the designed in weak/cheap part), you're going to break the next weakes part which is...
  4. Replies
    11
    Views
    346

    Well, I hope you took the fans off before you...

    Well, I hope you took the fans off before you washed your truck as no fans are waterproof. If so, that's the reason it stopped. If not, check for a broken wire or bad connection. I ran those for...
  5. Thread: Tire options

    by ROB311952
    Replies
    7
    Views
    279

    Good info. I was going to try a pair...

    [/QUOTE]
    Good info. I was going to try a pair of Badlands on my Monster Jam rims. I tore up the MJ tires on 3S off road because they were too thin too. I'll stick with Trenchers.
  6. Replies
    39
    Views
    1,157

    Did it require any mods to fit the pede?

    Did it require any mods to fit the pede?
  7. Replies
    33
    Views
    1,164

    Yes. I got it at Radio Shack.

    Yes. I got it at Radio Shack.
  8. Replies
    33
    Views
    1,164

    I got mine on ebay.

    I got mine on ebay.
  9. Replies
    4
    Views
    853

    I'd call em before you put in any of those new...

    I'd call em before you put in any of those new servos! Got to be a reason you're burning em out like that. I've got a Stamplede VXL 4X4 with 5.4" tires on it that I run on a short oval track and...
  10. Replies
    8
    Views
    591

    No dude, I wouldn't. However, I have found them...

    No dude, I wouldn't. However, I have found them to be quite knowledgeable. What he said about was actually true, and did happen to me. I can avoid the possibility of it coming unglued and not have...
  11. Replies
    33
    Views
    1,164

    This is becoming a pretty "hot conversion" ! I...

    This is becoming a pretty "hot conversion" ! I was running the dual integy fans on 3S with 13/54 gearing and getting about 145 deg. When I put in "The Mega", it dropped me down to 115. Well worth...
  12. Thread: Help!

    by ROB311952
    Replies
    1
    Views
    841

    Call Traxxas support. There's a fix for this but...

    Call Traxxas support. There's a fix for this but they don't publish it because if you do it wrong you can permanently damage the transmitter. They'll walk you through it on the phone and it will be...
  13. Replies
    8
    Views
    541

    When it was blinking green, it was trying to tell...

    When it was blinking green, it was trying to tell you throttle trim was not set right. When this happens, the right knob defaults to that so you can fix it. Adjust it until its constant green, then...
  14. Replies
    4
    Views
    853

    If you had correctly set your end points and that...

    If you had correctly set your end points and that isn't why you burned out the servos, then I'd call Traxxas.
  15. Replies
    12
    Views
    226

    You can't run a VXL motor with an XL5 ESC. VXL...

    You can't run a VXL motor with an XL5 ESC. VXL is 3 phase, XL5 is two phase. You can put in an VXL3S ESC and you can run a brushed motor (like the 21T Titan I recommeneded) with it; you just don't...
  16. Thanks poos. We tried out the new balanced tire...

    Thanks poos. We tried out the new balanced tire /wheel combo this afternoon on 3S (2.8 Trenchers on 3.2 Revolvers, stock offset front and Stablemax rear). Traction and handling was awesome. Going...
  17. Yeah, it's got to be one of these.

    Yeah, it's got to be one of these.
  18. They are almost completely different trucks....

    They are almost completely different trucks. Chassis, Steering, suspension, drive system, and lots of other stuff are totally different and this isn't a conversion. If you want 4wd, you need to buy...
  19. Replies
    12
    Views
    226

    Put in a Titan 21T for her. It will be a lot...

    Put in a Titan 21T for her. It will be a lot slower, run cooler, and last a real long time.
  20. Thread: Rollers

    by ROB311952
    Replies
    4
    Views
    163

    That's exactly what they do. The parts are worth...

    That's exactly what they do. The parts are worth more separetaly especially in modules, which also saves you money and time. That's how I get most of mine; the rest come from the LHS.
  21. Replies
    13
    Views
    461

    Use blue loctite (no heat to remove), tighten...

    Use blue loctite (no heat to remove), tighten secureily and let dry overnight. This gets is tight where it won't come off and you won't strip any threads in the pinion either by trying to compensate...
  22. Replies
    10
    Views
    706

    I have the 4X4 bumper on my 2pede. To fit it,...

    I have the 4X4 bumper on my 2pede. To fit it, you need to redrill the hole pattern and Dremel off the part that attaches to the front diff case. I added one screw also, through it into the stock...
  23. Replies
    4
    Views
    627

    Yes you need to replace the motor. The Velinion...

    Yes you need to replace the motor. The Velinion will run cool on 3S with 13/54 gears and the "Mega Heat Sink Fan". Look for the thread on how to do that. I used to fry them, then got the twin...
  24. Replies
    40
    Views
    2,321

    Try Dot 4 brake fluid and let it soak on there a...

    Try Dot 4 brake fluid and let it soak on there a while.
  25. This is very doable, but it's a tall order. ...

    This is very doable, but it's a tall order.
    First, getting it to go straight without having to trim.
    Make sure your servo is centering on startup with trim in the center. If it's not, go into the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4