Search:

Type: Posts; User: TOTONKA

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    460

    So is 5s on an EVX2 a bad idea? "Hot or smoking"...

    So is 5s on an EVX2 a bad idea? "Hot or smoking" doesn't sound good to me...

    And what about similarily spec'd packs of different brands?
  2. Replies
    4
    Views
    460

    LiPo failure, now what?

    I had a battery bulge last night and the speed/power of my Revo disappeared instantly. I threw it in the fire pit to dispose of it safely, now it's gone...

    I had a pair of GA 2s 40c that had about...
  3. Replies
    3
    Views
    449

    I've had that too, recalibrate...

    I've had that too, recalibrate...
  4. Replies
    6
    Views
    699

    I got a pair of 550s I'll sell for $25 Shipped.

    I got a pair of 550s I'll sell for $25 Shipped.
  5. Replies
    16
    Views
    1,057

    If you go to page 2 of this section of the forum...

    If you go to page 2 of this section of the forum about 1/2 way down you'll see a post called Dewalt conversion. Everything you need to know there. If speed is what you want, then by all means go...
  6. Replies
    16
    Views
    1,057

    I went to a dewalt conversion and a pair of 2s...

    I went to a dewalt conversion and a pair of 2s lipo last week, if I could get good enough traction (E-Maxx tires) I would probably be able to do wheelies, but for now they just spin till the rest of...
  7. Replies
    20
    Views
    2,005

    I just went Lipo and Dewalt on my Revo last week,...

    I just went Lipo and Dewalt on my Revo last week, the difference in power and runtime is rediculous! I have a kershaw designs LVC and a pair of Gens Ace 5000mah 40C hardshell, 21/68 gearing. I'm...
  8. Replies
    5
    Views
    476

    I emailed him at 8AM it's 4:00PM and had'nt heard...

    I emailed him at 8AM it's 4:00PM and had'nt heard anything so that's why I asked here.

    Also still curious about the low end voltage.
  9. Replies
    5
    Views
    476

    Issue with KD LVC

    I can't read the print on the PCB through the shrink wrap as to what cutoff setting I am using. I know the print is upright cause I can make out the V. So question is from top to bottom does it go>>...
  10. Replies
    13
    Views
    2,824

    I briefly had a 1/16 slash. It was way fast and...

    I briefly had a 1/16 slash. It was way fast and kind of hard to control (in snow) For me the size just didn't seem significant and the wheelbase was too narrow.

    I needed a more beastly rig. I...
  11. Replies
    8
    Views
    912

    I ran it last night outside without 15kg of meat...

    I ran it last night outside without 15kg of meat and 21/68 gearing. During a quick yet hard 7-8 minute run the motor shell was completely touchable as was the esc. I did bump the brush with my finger...
  12. Replies
    8
    Views
    912

    Yes, I forgot to include that....and yes I am...

    Yes, I forgot to include that....and yes I am dumb... hahaha
  13. Replies
    8
    Views
    912

    18t ordered.

    18t ordered.
  14. Replies
    8
    Views
    912

    Thx for the advice. Is 21/68 always too high?...

    Thx for the advice.

    Is 21/68 always too high? I was horsing around with the power by pushing my 30lb son around on an office chair and slamming him into the wall.. :-) was very fun! But maybe I...
  15. Replies
    8
    Views
    912

    Dewalt e-Revo - Heat issues please help

    Hi guys, I just switched my e-revo over to the dewalt this weekend.

    I am not sure what is considered acceptable temps. After 5 minutes of somewhat hard play my evx2 and motor were so hot I could...
Results 1 to 15 of 18