Search:

Type: Posts; User: shawn3putt

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    844

    Yeah i know that mah is where the run time comes...

    Yeah i know that mah is where the run time comes from. I was just wondering if the extra volt would make that much of a performance diff. The traxxas web sit says the esc can handle up to 9.6v and a...
  2. Replies
    4
    Views
    844

    8.4v nimh vs 9.6v nimh

    I have been toying with the idea of buying a 9.6v for my stock 2wd pede. I run a 8.4v currently but I want a bit more punch and lipo is not an option i dont want to deal with lipo and buying a new...
  3. need advise on breaking in new titan 12t

    I got a new engine as i must have gotten a bad one in my new truck or i didnt break in correctly. So im asking for known advice on proper break in. I have read Traxxas break but i do not have a area...
  4. Thread: Stampede

    by shawn3putt
    Replies
    13
    Views
    378

    I have the same issue. My pede is already running...

    I have the same issue. My pede is already running slower than when i got it for xmas. It eats up batteries and runs hot. I cant touch the motor after running and the run time on my 8.4v 3300mah nimh...
  5. Replies
    2
    Views
    136

    RPM bumper install

    I got my new RPM bumper for my pede.I go tthe 2wd "slash" bumper and also ordered the bumper mount that attaches to tranny :eek: not that kind of trann. So my ? is will I need the moter protector...
  6. Absoloot1 I did put the washers in. It's all...

    Absoloot1 I did put the washers in. It's all better but I unfortunaly already drilled hole in my tires and found
    It work a little but my other method of drilling two more holes on the inside if the...
  7. Replies
    4
    Views
    675

    bump:thumbup:

    bump:thumbup:
  8. ok so finally had a chance to really look at what...

    ok so finally had a chance to really look at what was going on with the front wheels. All the wheels had water in them. I drilled very small holes in the tires and got some out but not enough. So i...
  9. I saw some vids that do that but one said if you...

    I saw some vids that do that but one said if you drive in sand it will get in and make it worse. I live in Florida and the dirt here
    Has sand mixed in it. Hmm maybe I should microwave them since a...
  10. Ok will double check my hubs and tires. I did...

    Ok will double check my hubs and tires. I did notice the small holes in the rim. I even thought about drilling
    Two more bigger ones in each rim to allow more to drain out.
  11. I'll double check my hubs. So drilling small...

    I'll double check my hubs. So drilling small holes in the tire won't mess up the tire. I know I squeezed some out before I posted this so I'm sure there is some in there. I never noticed it before...
  12. wobbly front wheels after bearing upgrade

    I upgraded my wheels to bearings and now when its running the front wheels start to bounce. I checked and everything looks normal and tight. I even does it when i spin them while holding car in my...
  13. Replies
    11
    Views
    732

    Ok so the RPM kit needs a bumper mount that...

    Ok so the RPM kit needs a bumper mount that attaches to the trans. Does the Traxxas rear bumper require a seperate bumper mounting kit also. Also are any of the adjustable such as how far they stick...
  14. Replies
    0
    Views
    467

    Slash 4x4 front bumper Part #6735

    NEW Slash 4x4 front bumper. This rookie made a mistake and bought a slash 4x4 front bumper for a 2wd pede. I needed a 2wd slash bumper So this does'nt work and need to sell.
    MOUNTING HARDWARE NOT...
  15. Replies
    4
    Views
    675

    B U M P :thumbup:

    B U M P
    :thumbup:
  16. Replies
    11
    Views
    732

    Holy smokes look at all those shiny parts. Its...

    Holy smokes look at all those shiny parts. Its like a cyborg stampede. My traxxas has shiny rims and thats it.
  17. Replies
    11
    Views
    732

    Rpm parts seem to be the way most go.

    Rpm parts seem to be the way most go.
  18. Replies
    11
    Views
    732

    Time for some rear end protection

    Ok so i have managed to rip my body clips thru my new stamped in the rear in about 2 weeks. at $35 a body i looked into how to repair ripped body mount holes and other ares on you tube. So i bought...
  19. Replies
    4
    Views
    706

    looking for a new charger possibly

    Ok i bought a stampede and it came with a vision peak 2 charger. It sometimes will flash al three of the yellow led's that identify what amp you are charging at. I have it set at the proper cell...
  20. Replies
    27
    Views
    1,644

    I have a slash bumper that was the first thing I...

    I have a slash bumper that was the first thing I put on. It has saved me $$$$ already. So it sounds like Aluminum turnbuckles,castors and carriers are the next upgrade. I really like the look of the...
  21. Replies
    27
    Views
    1,644

    Ordered my bearings last night dor my pede. 8...

    Ordered my bearings last night dor my pede. 8 rubber sealed bearings for $12 on ebay. Cant wait to see the difference in performance. I noticed the other day while driving that when i do sharp or...
  22. Replies
    27
    Views
    1,644

    So when or if you guys upgrade to a stronger...

    So when or if you guys upgrade to a stronger motor or more efficient,stronger drivetrain such as axles do you buy aluminum
    Wheel hubs. I would think you would eat up the plastic ones with all the...
  23. Replies
    27
    Views
    1,644

    [QUOTE=dave00bear;5375415]Haha....Not to worry...

    [QUOTE=dave00bear;5375415]Haha....Not to worry they don't, Not sure what Teddyca was talking about there :unsure: :lol:
    That would explain why I didn't really notice the turnbuckle bearings on the...
  24. Replies
    27
    Views
    1,644

    Would the trans bearings help as well or should I...

    Would the trans bearings help as well or should I just worry about the wheels. Also I should be able to just take the new. bearings install them and when I want to upgrade the carriers...
  25. Replies
    27
    Views
    1,644

    I just want to do the front and rear wheel...

    I just want to do the front and rear wheel bearings for now. I was not even aware the turnbuckles had bearings. I also want to do the carriers and castor block but I'm going to wait till those...
Results 1 to 25 of 42
Page 1 of 2 1 2