Search:

Type: Posts; User: life_livin

Page 1 of 19 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    8
    Views
    305

    Yes both have the same part numbers.

    Yes both have the same part numbers.
  2. Replies
    0
    Views
    742

    *Mini E-Revo VXL For Sale!!!!!*

    Next up is a Traxxas Mini E-revo VXL. it will come with everything needed to rip and all original manuals along with a upgraded MG servo(Futaba s3102) and stock servo and 2 2200 2cell ***** lipos and...
  3. Replies
    0
    Views
    731

    WTB mini e revo pivot ball cap

    I broke one pivot ball cap on my mini e revo and was wondering if anybody has just one or a couple they will sell to me because I don't really need the pivot balls and ect. Included in TRA7033
  4. Thread: Ball diff?

    by life_livin
    Replies
    11
    Views
    483

    You could try the FLM diff, I think that it is...

    You could try the FLM diff, I think that it is sealed and you also could try and seal your stock diff and use fluid to tune it, I think there is a tutorial somewhere around here.
  5. Yes, a 2 cell is roughly the same voltage as...

    Yes, a 2 cell is roughly the same voltage as stock but the 3 cell will produce to much heat for stock gearing
  6. Replies
    7
    Views
    276

    I know I never thought that aluminum bulks were...

    I know I never thought that aluminum bulks were necessary for my type of driving but now I know they are necessary
  7. Replies
    7
    Views
    276

    Shock towers were undamaged but I am going to get...

    Shock towers were undamaged but I am going to get some FLM bulks soon, I did this after a 8-9 ft jump landing directly on the rear end, the front bulk broke after hitting a pole but I didn't notice...
  8. Replies
    7
    Views
    276

    All in a good day of bashing

    Just went out and bashed the t-maxx today, FLM here I come!
    http://i895.photobucket.com/albums/ac160/nick596/005.jpg

    http://i895.photobucket.com/albums/ac160/nick596/004.jpg
    ...
  9. Replies
    0
    Views
    889

    opti drive and sensor

    This is the optidrive off of my t-maxx 4909, the taps have been but for a jr receiver but it works perfectly and is in good shape
    $12 shipped...
  10. You can try priming it to get the fuel out

    You can try priming it to get the fuel out
  11. Replies
    4
    Views
    207

    If you cold hold ur thumb on there for 2 seconds...

    If you cold hold ur thumb on there for 2 seconds without burning your thumb it should be fine but it's best to get a temp gun, they are really handy and relatively inexpensive.
  12. Replies
    4
    Views
    207

    You may need to gear down, if you can't hold your...

    You may need to gear down, if you can't hold your thumb to the motor for two seconds then you are running to hot, just a little trick to use
  13. Fuel usually only gets into the pressure line...

    Fuel usually only gets into the pressure line when you first fill the tank to the top, after running the pressure should force out the fuel.
  14. Replies
    29
    Views
    1,523

    Then some nice sealed bearing should be just fine.

    Then some nice sealed bearing should be just fine.
  15. Replies
    29
    Views
    1,523

    I wouldn't pack the diff with grease, if you are...

    I wouldn't pack the diff with grease, if you are going to use grease I'd use a good green like Lucas red and tacky #2 that will not want to come off of the gears. That works a lot better than just...
  16. If when you set it down and it stalls and dies it...

    If when you set it down and it stalls and dies it sounds like a worn clutch spring to me but I would be wrong.
  17. Replies
    17
    Views
    1,062

    I am always breaking stub axles left and right,...

    I am always breaking stub axles left and right, I'm thinking of buying some flm cvds
  18. When you take the air filter off and look into...

    When you take the air filter off and look into the carb is the carb open more than 0.7-1mm open at idle? also go to full throttle and back a few times to see if it is getting stuck.
  19. Replies
    8
    Views
    1,032

    Not to thread jack or anything but I just thought...

    Not to thread jack or anything but I just thought I'd ask here instead of a whole new thread, I love the look of nitro truggy bodies where the body kind of angles backwards like the losi bodies and I...
  20. Replies
    5
    Views
    332

    Let us know how it goes, good luck!

    Let us know how it goes, good luck!
  21. Replies
    19
    Views
    294

    Those pro-line tanks are notorious for being...

    Those pro-line tanks are notorious for being fragile and break all the time, if you are going to upgrade to a bigger tank I suggest relocating your receiver pack and using a ofna violator tank. Do a...
  22. Replies
    29
    Views
    1,101

    Correct, the higher the kv is like the lower the...

    Correct, the higher the kv is like the lower the turns on a regular brushed motor, the lower the kv has more torque. You need to find a balance with kv gearing and heat.
  23. Replies
    13
    Views
    324

    Might be all talk, I've never seen a mammoth but...

    Might be all talk, I've never seen a mammoth but it isn't always a competition especially with monster trucks just have fun and don't give in is what I'd do but let's see what you have already and we...
  24. Replies
    10
    Views
    312

    I say either a shock shaft or a broken shock...

    I say either a shock shaft or a broken shock tower.
  25. Replies
    29
    Views
    1,101

    The vxl motor is a 3500 kv motor so that should...

    The vxl motor is a 3500 kv motor so that should be faster than the vxl.
Results 1 to 25 of 467
Page 1 of 19 1 2 3 4