Search:

Type: Posts; User: budlite28

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    44
    Views
    3,877

    6mm front stub axles for 2x4 slash

    does anyone make a 6mm front stub axle for a 2x4 slash that looks like thishttps://images.amain.com/images/large/tra/tra3637.jpg
  2. Replies
    12
    Views
    321

    I just did a set of traxxas tires & rims a few...

    I just did a set of traxxas tires & rims a few weeks ago. Used the oven @ 325 for 15 min and the tires peeled right off
  3. Replies
    4
    Views
    136

    thanks. I'll give it a try

    thanks. I'll give it a try
  4. Replies
    4
    Views
    136

    I have a MM2 & 1515 I could use, but i was saving...

    I have a MM2 & 1515 I could use, but i was saving it for another project
  5. Replies
    4
    Views
    136

    Mamba Max Pro w/ 1415 motor

    I just picked up new brushless erevo rolling chassis. I was wondering about using a Mamba Max Pro esc w/ CC1415 motor. What do you think of this setup for the Revo?. I am running HPI - 4731 Mounted...
  6. Replies
    1
    Views
    118

    MM2 quit working ???

    I was running the Max on flat dry dirt for about 10 minutes when it had a hickup. I thought it was a glitch but it ran for maybe another 20 feet then stopped completely. I noticed that the receiver,...
  7. Replies
    495
    Views
    482,468

    Sticky: http://i1272.photobucket.com/albums/y398/budlite28...

    http://i1272.photobucket.com/albums/y398/budlite28/EMaxx%20Buggy/RPMEMAXX001_zps6062a55d.jpg
    http://i1272.photobucket.com/albums/y398/budlite28/EMaxx%20Buggy/RPMEMAXX006_zpsd364a1bb.jpg...
  8. Replies
    193
    Views
    130,240

    Sticky: http://i1272.photobucket.com/albums/y398/budlite28...

    http://i1272.photobucket.com/albums/y398/budlite28/EMaxx%20Buggy/004_zpsd0bec836.jpg
    http://i1272.photobucket.com/albums/y398/budlite28/EMaxx%20Buggy/003_zps91c855f9.jpg...
  9. Replies
    495
    Views
    482,468

    Sticky: http://i1272.photobucket.com/albums/y398/budlite28...

    http://i1272.photobucket.com/albums/y398/budlite28/EMAXX/004_zpsd0bec836.jpg
    http://i1272.photobucket.com/albums/y398/budlite28/EMAXX/003_zps91c855f9.jpg
  10. Replies
    0
    Views
    503

    Pro-Line Rat Rod PRO3410-00 body

    Has anyone mounted the proline rat rod body onto the emaxx? It says its for the Revo & Summit but it think it would look bad on my emaxx that I'm building.
  11. Replies
    8
    Views
    254

    No, it's no swollen and my other 5 packs all...

    No, it's no swollen and my other 5 packs all charged equally. just this one pack didn't balance exactly. I'll just keep any eye on it
  12. Replies
    8
    Views
    254

    It's a traxxas and probably less than a year old

    It's a traxxas and probably less than a year old
  13. Replies
    8
    Views
    254

    LiPo Charging Question

    After charging my 11.1 25c 6400 mah battery w/ losi balancer. I got readings of 1) 4.15 2)4.15 3) 4.18. Is there a potential problem occuring with the balancing not being equal?
  14. cool, I think I'll give it a try, I have an extra...

    cool, I think I'll give it a try, I have an extra shaft to practice on:lol:
  15. there is no pin hole on the 3906 shaft, so is it...

    there is no pin hole on the 3906 shaft, so is it possible then to drill one or is the shaft hardened?
  16. Matching BL E-RevoSpur gear & slipper clutch to 3906 transmission

    Wondering if anyone has been able to matchup an E-Revo Spur gear & Slipper clutch to a 3906 transmission and if it is even possible. Just picked another old 3906 at a swap meet and would like to...
  17. Replies
    8
    Views
    745

    Well, it's been over a week and still not gear...

    Well, it's been over a week and still not gear and no response to email. I'm startin' to get angry
  18. Replies
    11
    Views
    1,564

    no, not yet, still waiting on tranny parts....

    no, not yet, still waiting on tranny parts. Couldn't seem to get everything at 1 place
  19. Replies
    11
    Views
    1,564

    Installed mine today. It didn't go quite as easy...

    Installed mine today. It didn't go quite as easy as you said. :) I installed on 3906 chassis and had cut 1 post down 7/16" and also grind a bit off the corner of my center brace but other than...
  20. Replies
    8
    Views
    745

    Just heard from Robin, appears all is good at UE

    Just heard from Robin, appears all is good at UE
  21. Replies
    8
    Views
    745

    no they got my money but I only got 1 gear not 2....

    no they got my money but I only got 1 gear not 2. And when I checked PayPal to see if I had any recall, it said their account had been suspended
  22. Replies
    8
    Views
    745

    Just found out their PayPal account is no good,...

    Just found out their PayPal account is no good, too
  23. Replies
    8
    Views
    745

    Problem with Unlimited Engineering

    Has anyone had problems in the past with these guys? I ordered a pair of steel idler gears from them and on Monday I received just one. I've tried phoning, faxing & emailing them with no response. In...
  24. Replies
    11
    Views
    1,564

    let us know how the fitment is. I've looking at...

    let us know how the fitment is. I've looking at this, too.
  25. I see Dollar Hobbyz has a complete tranny for a...

    I see Dollar Hobbyz has a complete tranny for a brushless Emaxx. What are the odds that it would fit an 3906 chassis and axles?
Results 1 to 25 of 49
Page 1 of 2 1 2