Search:

Type: Posts; User: brianf337

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    167

    Pm me I forgot to give you the cover that day.

    Pm me I forgot to give you the cover that day.
  2. Replies
    11
    Views
    103

    It's the SV34600

    It's the SV34600
  3. Replies
    11
    Views
    103

    I tried running the 30t pinion and 83t spur and...

    I tried running the 30t pinion and 83t spur and it hits thermal shutdown within 5 minutes.
  4. Replies
    11
    Views
    103

    At this point anything that I can run for more...

    At this point anything that I can run for more than 20 minutes will be fine.
  5. Replies
    11
    Views
    103

    Stampede 3s gearing setup sidewinder 3

    I've tried every gearing setup I could think of and the motor still hits thermal shutdown. What gearing setup should I run?
  6. It's definitely a rustler just an older version...

    It's definitely a rustler just an older version to the newest one because it doesn't have a 2.4 ghz radio but all the parts are the same as the newest one.
  7. Replies
    0
    Views
    130

    1/16 revo gearing

    I know this has been covered many time but I'm running a 3s lipo with a 45t spur and can't remember which pinion I had in my old 1/16 slash to not get hot. What would you recommend for hard bashing?
  8. Thread: Gearing help

    by brianf337
    Replies
    3
    Views
    121

    Gearing help

    What gearing would I have to use to get the most top speed?
  9. Replies
    9
    Views
    265

    I've had the truck since the first day it came...

    I've had the truck since the first day it came out and the new slipper pad vs the old looks nothing like it. I just have to put it back together and test it.
  10. Replies
    9
    Views
    265

    Yes it does

    Yes it does
  11. Replies
    9
    Views
    265

    The pad looks pretty worn down I've had the truck...

    The pad looks pretty worn down I've had the truck since the first day it came out. Tightening the slipper clutch doesn't make a difference and diffs are fairly new.
  12. Replies
    9
    Views
    265

    1/16 revo won't move

    If the slipper clutch pads are bad will it cause the truck not to move?
  13. Replies
    1
    Views
    156

    Rustler Transmission

    I have a rustler 3710 with the black chassis, Can I use the newer gears in the old transmission?
  14. Replies
    2
    Views
    225

    I figured it out I wasn't paying attention and...

    I figured it out I wasn't paying attention and put it in backwards.
  15. Replies
    2
    Views
    225

    Front wheels don't spin

    I just changed the front diff in my rally and the front wheels don't spin at all only the rear did I miss something?
  16. Replies
    8
    Views
    828

    1/16 slash tires

    What options do I have as far as tires for the slash? Can I use the trenchers?
  17. Thread: 1/16 mustang

    by brianf337
    Replies
    7
    Views
    1,045

    1/16 mustang

    How can I lower the car more than it already is it flips over way too easily on high speed runs.
  18. Replies
    7
    Views
    389

    You can't use the sway bars if you use the RPM...

    You can't use the sway bars if you use the RPM bumper.
  19. Replies
    4
    Views
    413

    Inside the transmission

    Is there supposed to be any kind of grease in the transmission. Mine is dry and it looks like there's never been any type of grease in it.
  20. Replies
    5
    Views
    542

    Ok thanks because I thought I forgot something.

    Ok thanks because I thought I forgot something.
  21. Replies
    5
    Views
    542

    Steel Center drive shaft

    Where do you put the o rings they give you because in the directions it doesn't say anything about putting the o rings on so I left them off.
  22. Replies
    5
    Views
    331

    You can but you should watch your temperature on...

    You can but you should watch your temperature on the motor.
  23. Summit drive shafts to the Mini Rvo driveshafts

    Do I have to change anything other than the drive shafts? My friend keeps breaking them after every week of running.
  24. Replies
    6
    Views
    403

    OK thanks because if I just buy a new plastic one...

    OK thanks because if I just buy a new plastic one the same thing will happen again.
  25. Replies
    6
    Views
    403

    Do they hold good and won't pop out on 3s?

    Do they hold good and won't pop out on 3s?
Results 1 to 25 of 89
Page 1 of 4 1 2 3 4