Search:

Type: Posts; User: eschult

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    14
    Views
    851

    R u kidding me!!!!!!!!

    R u kidding me!!!!!!!!
  2. Replies
    14
    Views
    851

    can not post pics yet. have to read about how to...

    can not post pics yet. have to read about how to post


    Rc Driver magazine. August 2012 issue Page 66. I have to create a photo bucket account in order to post a pic. Not tonight. LOL. I...
  3. Replies
    14
    Views
    851

    I think that pic is awsome!!!!!! Almost home...

    I think that pic is awsome!!!!!! Almost home from a few day getaway and will take a pic of mag photo and post.
  4. Replies
    14
    Views
    851

    Sorry as I wish I could. Can not post links. its...

    Sorry as I wish I could. Can not post links. its in the mag as an upgraded grave digger getting some air off of a jump in my back yard.
    Thanks, eric. Jacksonville fl.
  5. Replies
    14
    Views
    851

    Rc driver magazine

    My stampede was published In rc driver magazine!!!!!!!!!! pretty cool seeing it in a mag.
  6. Thread: drive shafts

    by eschult
    Replies
    5
    Views
    520

    drive shafts

    What are you guys using for upgraded drive shafts????? I use the mip's for my pede and they are very good, but pricey. I bought the GH and i have not had one last more than a few minutes. the pins...
  7. That rustler does not seem all that fast to be...

    That rustler does not seem all that fast to be honest. i think my 1/16 revo running on a 3 cell 1000mah 30c would smoke it???? I would not have bought the pede for speed. It can move but that's not...
  8. Thread: Wheels

    by eschult
    Replies
    6
    Views
    323

    I thought you were meaning that you glue a good...

    I thought you were meaning that you glue a good wheel. You are glueing just to get more life out of the one that is already toast?????
  9. Thread: Wheels

    by eschult
    Replies
    6
    Views
    323

    Really??? Just superglue???? I have not...

    Really??? Just superglue???? I have not heard of this trick yet. Does it really work????
  10. Thread: Wheels

    by eschult
    Replies
    6
    Views
    323

    Wheels

    I have now stripped two of the inside rims. Anyone know of any stronger rims to get that will not strip as easy???????
  11. Replies
    46
    Views
    5,020

    I thought by adding this longer rudder the...

    I thought by adding this longer rudder the spartan wouldm be more agile??????
  12. Thread: turning

    by eschult
    Replies
    1
    Views
    233

    turning

    Anyone know why the spartan does not turn like a normal vhull???? I have played with many other vhulls (Super vee r, outlaw, outlaw jr, minimo, ect.) but the spartan does not have the same...
  13. Replies
    5
    Views
    462

    Had to remove the m as they were so tight up...

    Had to remove the m as they were so tight up against the bearings it was causing them to rub. NOot sure???? anyone use these w/ the mip cvd's???
  14. Replies
    43
    Views
    1,124

    I just got around to doing this . i used some...

    I just got around to doing this . i used some jbweld instead based on thats what it looked like when I removed the magnet. Long story short is that it works. Ran it all day on mostley 3 cells. No...
  15. Replies
    5
    Views
    462

    finished installing them tonight. Nat crazy about...

    finished installing them tonight. Nat crazy about all the play it the tires. Only way to get the hubs to fit was by removing the washer form the bearing. Not sure if thats a great idea as i am about...
  16. Replies
    5
    Views
    462

    wheel extenders

    Anyone know where to find directions to install these??? Got em from the TOYZ and no directions. I think I can figure it out but want to make sure i am correct.
  17. Replies
    43
    Views
    1,124

    sorry, Loctite 480

    sorry,
    Loctite 480
  18. Thread: Bad Motor???

    by eschult
    Replies
    12
    Views
    328

    Sorry, It is Loctite 480. Entire thread on RCG...

    Sorry,
    It is Loctite 480. Entire thread on RCG about using this on failed magnets inside brushless motors
  19. Thread: Bad Motor???

    by eschult
    Replies
    12
    Views
    328

    Locktite 190 is the stuff. Been tested by others...

    Locktite 190 is the stuff. Been tested by others and already and proved to be successful.
  20. Replies
    43
    Views
    1,124

    Ordered a new brushless 2 days ago. just seeing...

    Ordered a new brushless 2 days ago. just seeing if i can salvage this one???
  21. Replies
    43
    Views
    1,124

    Did some reseach andfound that the magnet coming...

    Did some reseach andfound that the magnet coming unglued is pretty common. So if i send a motor in and it only needs to be re-glued????? Thats a heck of a profit!!!!!!!!!!!! BTY Found that...
  22. Replies
    43
    Views
    1,124

    it was a 2 cell on its first run for the day....

    it was a 2 cell on its first run for the day. Motor went on 1/2 the pack. Have cooling fan and heatsink. The heat wasnt the issue. Motor was not hot at all. Thats why i thought it was one of the...
  23. Replies
    43
    Views
    1,124

    So if the velineon only consists of a few parts,...

    So if the velineon only consists of a few parts, can, magnet, bushings, ect. what can actualy break inside the motor??? If the bearings were down you just buy the rebuild kit. Just wondering what...
  24. Replies
    43
    Views
    1,124

    ok. So i need to look for 540 can size and around...

    ok. So i need to look for 540 can size and around 3500 kv.
  25. Replies
    43
    Views
    1,124

    Thanks. Whats the best can size to go with???

    Thanks. Whats the best can size to go with???
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4