Type: Posts; User: Sir.Yilufa
Anyone can help me out with a problem?
Traxxas does not have distributer around my region.
I've supported Traxxas but it seems that it is very difficult to find replacement parts for my revo.
anyone can find the traxxas tqi app?
I cant find it.
My servo broke down just 5 days after purchase.
It cost m more to sent in my servo for replacement.
I hope traxxas do something about their international warranty so that they could gain more...
Care to share a photo of the set up with the coat hanger to the rockers?
I'm also trying to cut cost too and will be sawing off the drive shaft so that it'll fit the shorter width.
I always prefer...
I would like to covert my Merv into a pure on road car.
But I'm not sure what parts are required....
From what i know I need the follow
1) turn buckle
2) toe link
3) front and rear A-arms
Why do some guys here install dirt hwangs?
isnent heavier wheels cause more unsprung weight?
what is the benefits of using heavier wheels as I see more cons then pros?
please share your thought.
Does anyone knows the full gear ration for the E Revo?
I mean including the gear in the differential all the way to the wheel?
eg .... 28:50:10:20
I have a question about the XO 1.
The Traxxas team uses the downwards forces to stabilize the vehicle during high speed.
will there be somehow too much down forces that the chassis is sliding on...
select the whole design, paste it into another new file.
similar to what you encounter with read only files in microsoft office.
Btw, i would recommend changing the micro servo to accommodate a...
Good news everyone.
There is a free CAD software that is able to open and edit DXF file that the revo chassis is in.
It is called Draftsight from solidworks.
However, its a 2D instead of a 3D.
Is it possible for me to use a submit shell on and E Revo?
It seems that the rear wing of the revo will get in the way of the submit shell.
Do I have to change any of the mountings?
actually the stock revo have 2 drive shaft, one short and one long.
I'm thinking if i should use 2 long drive shaft so that I could have a longer wheel base.
U guys have any advise?
can you upload the file again?
The link seem to be not working.
they only include the top and bottom chassis.
Care to share the battary doors and most importantly the motor mount?
I can use that file and personalize it...
I have a laser cutting machine at work...
what cell are you using?
how do you guys solve wobbling wheels?
My revo's right front wheels have wobbling issues.
The wobbling causes the vehicle to drift to one side.
Using steering trim does not solve the problem as...
I love the GPM CVDs.
They seems so solid and sturdy.
Anyone knows where can I get them?
have anyone have any issue with the radio controller?
I feel that the steering wheel on it have too little turn.
It's as if like those cheap toy grade controller that have only full left or full...
RPM arms + servo upgrade
Is there a problem if i connect the servo connector in reverse?
There are 3 pins in the servo connector, mine seems to be able to connect in both ways.
Just wondering if it will damage the...
the merv was running straight and suddenly it surve to the right and turn upside down.
when it was flip over, I notice that there is a blinking light from the receiver and the vehicle is not...
will installing a beadlock reduce the chances of flipping over since it have more weight below the chassis?
What would be the pros and cons of installing this wheels?
how do you guys usually secure your heat sink to the motor?
Mine usually slide off the motor.
I am very interested with your DIY anti sway bar.
Can you be able to take some close up photos of it?
If possible can you share with us how it is being made?
I've used stock talons for my runs.
But I switch to submit caryons and found it to be better..
However, it will requires lowering the gearing