Search:

Type: Posts; User: djbrun

Page 1 of 13 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    8
    Views
    259

    Same here.

    Same here.
  2. Replies
    23
    Views
    2,013

    I have run many different exhaust systems over...

    I have run many different exhaust systems over the years, started using Borla back when I had my mustang. I went through 4 different systems on my Vette until I went back to Borla. When it comes to...
  3. I just took a trip to Japan and was thinking of...

    I just took a trip to Japan and was thinking of doing this myself, the battery was the issue for me. I would just ship it home if I were you, if this would be an extra bag it is gonna cost you about...
  4. Thread: new mustang!

    by djbrun
    Replies
    38
    Views
    1,487

    To me, it looks like the (Aston Martin inspired)...

    To me, it looks like the (Aston Martin inspired) front end just doesn't go with the rest of the car. I like the rear pillar design change, it really needed that IMO. The front sloping down a little...
  5. Replies
    18
    Views
    784

    I run a MM/2650 set up in my rig, and the stock...

    I run a MM/2650 set up in my rig, and the stock system in the HCG I built for my wife. I am a basher only but, the stock system is not fast enough for me (with proper gearing for low heat) for our...
  6. Replies
    27
    Views
    1,455

    My RPM arms are bent after one big air session,...

    My RPM arms are bent after one big air session, making them longer would just increase the leverage at the shock mounting points. This would make it worse for me.
    I also have a 3-d printer at work,...
  7. Replies
    27
    Views
    1,455

    I just put these on my back slash so I could put...

    I just put these on my back slash so I could put some bigger wheels, you guys are making me think I made a bad choice. I got tired of bending the rpm a-arms and was going to go back to stock. Do you...
  8. Replies
    30
    Views
    1,254

    I didn't see this till today, and you are very...

    I didn't see this till today, and you are very welcome. Glad too see the truck coming along, as others mentioned the MIPS are very tough. I run the mm/2650 in my lcg slash with the MIPS and I finally...
  9. Replies
    7
    Views
    445

    My set up sees lots of air time and bad landings,...

    My set up sees lots of air time and bad landings, have not had any issues thus far.
  10. Replies
    6
    Views
    468

    Thank you very much!

    Thank you very much!
  11. Replies
    7
    Views
    445

    The thread name is "my buggy body"

    The thread name is "my buggy body"
  12. Replies
    7
    Views
    445

    I will need to look up how to link to another...

    I will need to look up how to link to another thread. I have one and posted it, let me look.
  13. Replies
    6
    Views
    468

    I have MIPS on my 2650/mm backslash, just broke...

    I have MIPS on my 2650/mm backslash, just broke one today. But it did last quite a while, pretty heavy though. Are the tenons or traxxas any lighter?
  14. Replies
    6
    Views
    468

    Best axles for a rustler?

    I do not use my Rustler much anymore, but I took it out today and broke an axle on flat ground pretty quick. What axles would you recommend for a 2400/mmp 3s set up? It is just a parking lot racer.
  15. Thread: Slash 4x4 tires

    by djbrun
    Replies
    10
    Views
    1,340

    I had street fighters on my rustler and they flat...

    I had street fighters on my rustler and they flat spotted on one spin out while slowing down. They were brand and balanced, and then junk in 5 minutes. Now of course a 4X4 would be less likely spin...
  16. Thread: A arms

    by djbrun
    Replies
    6
    Views
    299

    El Sob, I like that response! Yea, I broke the...

    El Sob, I like that response! Yea, I broke the stocks when I was learning how to drive as well. I will try the stockers again now that I am proficient at breaking my rig.

    Today I broke an MIP...
  17. Replies
    13
    Views
    2,006

    I use them more and more since my local hobby...

    I use them more and more since my local hobby shop is stocking less and less. Quick service and usually have what I need. Love this place.
  18. Thread: A arms

    by djbrun
    Replies
    6
    Views
    299

    A arms

    I have been using rpm a arms, but need something better for bashing. They bend pretty easy and I lose ground clearance the more they bend.
  19. Replies
    6
    Views
    324

    Where in Nor cal? I probably have a few sets of...

    Where in Nor cal? I probably have a few sets of wheels and tires (Stock). If you are close enough to stop by, you can what ever you want, free of charge.
  20. Replies
    8
    Views
    364

    The parts that broke (Besides the chassis and...

    The parts that broke (Besides the chassis and drive shaft) were original from when I purchased this as a rally. They had a lot of air miles on them. I am pretty happy with it, my other buggy which...
  21. Replies
    8
    Views
    364

    sean 1214- I have a body but the repeated jumps...

    sean 1214- I have a body but the repeated jumps caused the body to rip out just before this jump, so I left it off.

    Here is what it looked like....
  22. Replies
    194
    Views
    10,505

    Looks clean, I love that body style. How many...

    Looks clean, I love that body style. How many miles does she have on her?

    DJ
  23. Replies
    8
    Views
    364

    Good day of bashing!

    Took my backslash out today along with another buggy, I successfully broke them both in dramatic fashion. So, it was a good day. Just wondering what you guys have done for your receiver box if you...
  24. Replies
    795
    Views
    73,560

    Just received my Mamba monster V2 today, so I...

    Just received my Mamba monster V2 today, so I will be launching my slash this weekend.
  25. Replies
    795
    Views
    73,560

    I had a similar situation with mine, concrete is...

    I had a similar situation with mine, concrete is not very forgiving.
Results 1 to 25 of 310
Page 1 of 13 1 2 3 4