Search:

Type: Posts; User: kevsgonefishing

Page 1 of 14 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    18
    Views
    671

    I was wondering if there was any difference in...

    I was wondering if there was any difference in the gear boxes, trans running gear etc???
  2. Replies
    18
    Views
    671

    Brushless vs Brushed

    I am considering buying a Stampede, I saw at my local hobby store a brushed version. Other than the obvious brushed motor, plastic camber links and the plastic drive shaft are there any other major...
  3. The dual brake set up is the best fix for the...

    The dual brake set up is the best fix for the Jatos SUCKY brakes!!!
    But it looks like you need to ahjust the throw on your controller and do the fuel line or "pen mod" on your linkage.
    Search...
  4. Replies
    25
    Views
    3,721

    Dang I had alot of spelling errors in that...

    Dang I had alot of spelling errors in that post.......
  5. Replies
    25
    Views
    3,721

    Looks like you did yhe Rustler mod on your feont...

    Looks like you did yhe Rustler mod on your feont hubs for a better variety of heels???
  6. Oh yeah and stay away from alum.....its junk, go...

    Oh yeah and stay away from alum.....its junk, go with RPM parts
  7. Andy, I cant help you on the servo pic. The...

    Andy, I cant help you on the servo pic. The second pic is your slipper, if there is a pad missing replace the slipper. You can fing all the part#s on this website under products and just pic your car...
  8. Replies
    10
    Views
    1,186

    front or rear arms???

    front or rear arms???
  9. Replies
    7
    Views
    623

    Who makes an 8mm carb to fit the 3.3???

    Who makes an 8mm carb to fit the 3.3???
  10. Replies
    7
    Views
    623

    Than youll need to improve the braking by going...

    Than youll need to improve the braking by going with the dual disk set up....its a must
  11. Replies
    7
    Views
    623

    Go with Revo rearing

    Go with Revo rearing
  12. Replies
    12
    Views
    709

    Top Dead Center, meaning the piston is at its...

    Top Dead Center, meaning the piston is at its highest point at the top of the stroke.
  13. Replies
    8
    Views
    852

    You can also just use any metric scoket and a...

    You can also just use any metric scoket and a ratchet that fits, I forget what size it is but I just grabbed one out of my tool box.
  14. Replies
    8
    Views
    817

    The rears only will work on the Jato off of any...

    The rears only will work on the Jato off of any traxxas vies with 12mm hexes, the fronts will only work if you do the Rustler front spindle mode seen on the forum here, Im doing that mod now
  15. Replies
    3
    Views
    634

    Well first make sure your servo for the...

    Well first make sure your servo for the throttle\brake is going both ways and all the linkage is hooked up. The stock brakes SUCK on these cars. Look at the manual on this site and you can see how it...
  16. Replies
    15
    Views
    2,393

    I havent even put the axle spindle in yet, I also...

    I havent even put the axle spindle in yet, I also tried two different 1\8 bits. I used the RPM part# you gave me for the Rustler block. I did run the drill bit through the stock Jato one and it...
  17. Replies
    15
    Views
    2,393

    OK so I ran the 1\8 drill bit through the new...

    OK so I ran the 1\8 drill bit through the new front hubs and I cant get the king pin to slide through easly, I actually have to drive it through with a punch. What is the next size up I can use to...
  18. Replies
    15
    Views
    2,393

    I got all the parts for the conversion that...

    I got all the parts for the conversion that Slayer refers to, I'm gonna do the install this weekend...wish me luck
  19. Replies
    12
    Views
    3,772

    I got my pull starter and ignighter today and...

    I got my pull starter and ignighter today and I'll install it this weekend....wish me luck
  20. Replies
    12
    Views
    3,772

    So it doesnt look like traxxas makes a pull start...

    So it doesnt look like traxxas makes a pull start for this, either that or I just havent found it. Whar brand pull start did you guys get and are thay pretty straight forward as far as installation?...
  21. Id like to see some pics of your first conversion

    Id like to see some pics of your first conversion
  22. WOW thats ALOT of almuninum!!! but prolly one of...

    WOW thats ALOT of almuninum!!! but prolly one of the coolest e-jato conversions ever. Imagine how much faster it would be with more plastic than metal.....nice job!!!
  23. Replies
    12
    Views
    1,160

    Is the OS 21TM a faster engine than the 3.3?

    Is the OS 21TM a faster engine than the 3.3?
  24. Replies
    5
    Views
    907

    Tbull what buggy wheel mod are you talking about?...

    Tbull what buggy wheel mod are you talking about? The Jato has a pretty wide wheel base stock.....
  25. Replies
    12
    Views
    3,772

    Why could it be a pain if Im not good at tuning?...

    Why could it be a pain if Im not good at tuning? I havent had it long and still trying to figgure that all out
Results 1 to 25 of 340
Page 1 of 14 1 2 3 4