Search:

Type: Posts; User: DaBasher

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    276

    I use loc tite on the screws. And always take a...

    I use loc tite on the screws. And always take a solider iron to them when getting ready to remove the screws. The heat helps break the loc tite. I never use grease as I was afraid it would attract...
  2. My 1/10 scale was doing that and it was because...

    My 1/10 scale was doing that and it was because the button on the esc we stickng. It wouldn't always go to training it just depended wher the button decided to release. I'm not real sure about...
  3. Replies
    11
    Views
    198

    Most racers at my local track run 50k in the...

    Most racers at my local track run 50k in the center diff. My slash kind of does what you are talking about coming out of the long straight while letting off the throttle and sliding out. I've...
  4. Replies
    2
    Views
    185

    I tried mine like that once but it was just to...

    I tried mine like that once but it was just to bundle some. In some spots it it was kinda hard to use , for me anyway. I just ordered the MIP metric set. Yea it was about 36 bucks but it will be...
  5. It could be a stiffer preload could be causing...

    It could be a stiffer preload could be causing you to push more through the turns. If the tire has a harder compound that could also cause you the push through the turns. The only other thing I...
  6. Thread: Axel

    by DaBasher
    Replies
    20
    Views
    526

    I have and would go with the MIP x duty. If you...

    I have and would go with the MIP x duty. If you race you might want to try the MIP racing shafts. My son has the MIP racing shafts and we run at the local track a lot. I like the way my slash 4x4...
  7. Replies
    9
    Views
    529

    Yes I prefer 2s for offroad at least for the...

    Yes I prefer 2s for offroad at least for the areas I have to run at. Usually either at the local track or small area at the house where I've got plans on building a track. I don't even own a 3s...
  8. Thread: gearing?

    by DaBasher
    Replies
    5
    Views
    189

    Yes the fan comes on when the esc reaches a...

    Yes the fan comes on when the esc reaches a certain temp.
  9. Replies
    9
    Views
    289

    Just bashing around a 13/54 with a 2s should be...

    Just bashing around a 13/54 with a 2s should be fine for the most part. Always watch your temps with a temp gun and check regularly. As your driving style and terrain will also affect the temps....
  10. Replies
    31
    Views
    1,045

    If you did glue them I hope you used silicone...

    If you did glue them I hope you used silicone instead of some kind of ca glue as silicone is a little easier to remove without damaging your wheels or tires
  11. Replies
    12
    Views
    355

    Lol. Just get the slash 4x4 and upgrade it as...

    Lol. Just get the slash 4x4 and upgrade it as needed. You will figure out what everything as time goes.
  12. Replies
    12
    Views
    355

    The slash 4x4 is a great choice. I have a HCG...

    The slash 4x4 is a great choice. I have a HCG and my sone has the LCG. I have the MIP extra duty shafts and he has the MIP racing shafts. Both sets of MIP shafts have been well worth the money....
  13. Replies
    5
    Views
    297

    Yes mine did that too. I took the rear end off...

    Yes mine did that too. I took the rear end off and put it back on and it seemed to be better but was still there. I did the same as rich2 just ran it out. Just took about 2 runs down the straight...
  14. With a dermal. There are videos on YouTube. It...

    With a dermal. There are videos on YouTube. It Takes patience. After cutting with the dermal with like a metal file bit take a rattail file and get what's left of the melted plastic off. It takes...
  15. As you said maybe a bad bearing or your slipper...

    As you said maybe a bad bearing or your slipper was to loose letting it slip all the time and creating excessive heat. Which would also cause your pads to wear out
  16. http://i134.photobucket.com/albums/q112/HOPD1/null...

    http://i134.photobucket.com/albums/q112/HOPD1/null_zps1d33221d.jpg
  17. Replies
    12
    Views
    819

    I use the integy heatsink without the fan as I...

    I use the integy heatsink without the fan as I never have had a fan last more than 5 to 10 battery packs. The heatsink was doing that to my wires. I just too a wire tie and pulled the wires away...
  18. Cut out like my body is ( see above ) doesn't...

    Cut out like my body is ( see above ) doesn't really weaken it very bad. The more and bigger holes you cut can create a weak spot. I have seen some people cut out the windows and most all of the...
  19. This is how I have mine cut. It doesn't seem to...

    This is how I have mine cut. It doesn't seem to hurt the aerodynamics in the straights but does seem to help with the body lift on the straights and parachuting on jumps. I haven't decided if I...
  20. I just notched out around the bumper a bit to...

    I just notched out around the bumper a bit to make it fit. And also lifted the body a bit. http://i134.photobucket.com/albums/q112/HOPD1/null_zps3a6073f5.jpg
  21. Replies
    12
    Views
    367

    Since I upgraded to the MIP xduty shafts I really...

    Since I upgraded to the MIP xduty shafts I really haven't broken a lot. Over the last 3 years maybe 2 a arms and one c hub. In either run at the track or in a big open dirt area so I dont run into...
  22. Replies
    12
    Views
    367

    The slash 4x4 is a great choice. Everyone will...

    The slash 4x4 is a great choice. Everyone will have their on opinion but I would go with a standard and use the extra money to upgrade the axle shafts to the MIP extra duty shafts ( front and rear...
  23. Replies
    36
    Views
    1,180

    Its probably not this but have you checked to...

    Its probably not this but have you checked to make sure the servo and speed control are plugged in the correct slots on the receiver. I had mine plugged in wrong one time and it was doing some...
  24. Replies
    5
    Views
    172

    Mine worked fine on my slash 4x4 lcg with traxxas...

    Mine worked fine on my slash 4x4 lcg with traxxas hubs. Well it would rub just a bit when the shocks bottomed out. I just had to put a small spacer on the front and rear shock shafts
  25. Replies
    16
    Views
    675

    Yes either way you got a good deal. I bought a...

    Yes either way you got a good deal. I bought a stampede 4x4 with the stock motor and esc for $100 and converted it to a LCG slash 4x4 to set up for racing but if I was just bashing I would stick...
Results 1 to 25 of 97
Page 1 of 4 1 2 3 4