Search:

Type: Posts; User: wesgreen

Page 1 of 12 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    11
    Views
    1,525

    What do you mean by elongating the holes on the...

    What do you mean by elongating the holes on the chassis?
  2. Replies
    11
    Views
    1,525

    single servo conversion problem ????

    Just got a Hitec 7955TG. The mounting holes don't line up. The front two holes line up perfectly, but the back mounting tabs don't reach quite far enough.
    Also, the screw holes on the included...
  3. Replies
    3
    Views
    1,689

    aluminum pushrod question

    I can't find the aluminum pushrods for the p2 rockers which is what I run. Should I get the p1 or p3 pushrods? I'd like to keep the p2 rockers on.
  4. Replies
    2
    Views
    972

    shimming diff question

    What size shims do I need?
  5. Replies
    6
    Views
    1,621

    true track vs rear tekno carriers??

    Well, you can't have them both. I'm serious thinking about ditching my true track in favor of the tekno carriers. I just wanna get all of the slop out.

    Anyone have any opinions or suggestions?
  6. Replies
    18
    Views
    2,860

    The only difference in the 3.3 and the erbe diffs...

    The only difference in the 3.3 and the erbe diffs is the I-bar inside the cup. I've been running a 3.3 diff without the I-bar for a while. I've never had any issues with the spider gears that the...
  7. Thread: Compressor??

    by wesgreen
    Replies
    13
    Views
    1,819

    You could just get a 2-3 gallon tank and fill it...

    You could just get a 2-3 gallon tank and fill it up before you go out. Those are very portable and light. You could fill it up at any gas station air pump.
  8. Replies
    7
    Views
    1,882

    Alright, thanks for the help

    Alright, thanks for the help
  9. Replies
    7
    Views
    1,882

    I'm running true track in the rear and I don't...

    I'm running true track in the rear and I don't really wanna go back to the toe links out back. Probably goon get the tekno's for the front. Will the maximizer hubs work with my rulux halfups?...
  10. Replies
    7
    Views
    1,882

    Time for upgrades! Few questions

    My ERBE is past due a good servicing so I've decided fix'er up a bit. My list thus far includes the following:

    -single servo (hitec 7955tg)
    -golden horizons steering arm
    -traxxas aluminum tie...
  11. Replies
    14
    Views
    1,963

    It will work, but I wouldn't recommend it. The...

    It will work, but I wouldn't recommend it. The molex connector is gonna get really hot and it will eventually give out.
  12. Replies
    7
    Views
    1,855

    Yeah, I wrote that sig about 3 years ago. I've...

    Yeah, I wrote that sig about 3 years ago. I've had a revo 3.3 and its since become a parts truck for my ERBE. lol

    I tried to use CA glue and it didn't work. When I installed the tires on the...
  13. Replies
    7
    Views
    1,855

    badlands (insert/foam) question

    I accidentally tore one of the foams for my badlands in half. What do yall recommend as a good replacement? Links would be great! Thanks guys.
  14. Replies
    4
    Views
    1,856

    Another slipper question

    I ended up burning out my slipper after about 6 months of use. I pulled the one from my 3.3 revo and put in on my ERBE. I used the original nut from the erbe. It works fine now but the nut won't...
  15. silly body mount question, still need help though

    I broke the rear body mount, the thing that the wing mount attaches to. I was going to take the one from my 5309 3.3 revo but the parts are different. The e revo mount has 3 screw holes attaching...
  16. Thread: heat question

    by wesgreen
    Replies
    3
    Views
    1,843

    No, if all else remains constant; driving style...

    No, if all else remains constant; driving style and what not, then the motor will run hotter on 6s then on 4s. The motor turns at a higher rpm with the increased voltage which causes the temp...
  17. Replies
    2
    Views
    848

    Help with MMM switch problem

    After a hard crash the other day my MMM just cut off. I wiggled the wires on the switch a little and got it to turn back on so I know that is the issue. However, it won't stay on. I've read about...
  18. Okay, the best bashing setup I've come across is...

    Okay, the best bashing setup I've come across is as follows... Install the optional included springs, blue in rear, silver in front. Install the optional steering stop. Get some rulux 1/2 offset...
  19. Thread: ruined a lipo

    by wesgreen
    Replies
    6
    Views
    990

    ruined a lipo

    Had a good bash session earlier on 6s. When I got done one of the 3s 5k 20c *****s was puffed pretty bad. I let it cool and tried to charge it but it wouldn't take a charge cause the voltage...
  20. Thread: Couple ?'s

    by wesgreen
    Replies
    5
    Views
    847

    Couple ?'s

    I can't seem to get my steering centered properly. I've taken the horns off both servos and centered them, but it still wants to pull to the left a good bit, especially under hard acceleration. Any...
  21. Replies
    7
    Views
    939

    I do a few runs on 4s and a few on 6s, but I...

    I do a few runs on 4s and a few on 6s, but I mainly run on 5s. It seems like the perfect balance. I'm geared 18/54 on usually run off road. I did break an a arm earlier today. I hit a tree about...
  22. Replies
    4
    Views
    738

    I got it figured out now. Much easier than I...

    I got it figured out now. Much easier than I thought. It took maybe 5 minutes to rebuild one.
  23. Replies
    7
    Views
    939

    Finally got'er dialed in

    It took about a month, but I finally got me ERBE running really good without breaking driveline parts on every run. :D I have my slipper set just right, and my punch control is at 20%. I finally...
  24. Replies
    4
    Views
    738

    I gotcha. I was just trying to remove the larger...

    I gotcha. I was just trying to remove the larger pin while leaving the smaller pin in place. Guess I'll have to deal with those tiny e clips.
  25. Replies
    4
    Views
    738

    rebuilding axles???

    How exactely do you rebuild them? I can't seem to get the u joints apart.
Results 1 to 25 of 298
Page 1 of 12 1 2 3 4