Search:

Type: Posts; User: rock-rod

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    6
    Views
    83

    The HD slipper kit from traxxas is cross...

    The HD slipper kit from traxxas is cross compatible. It has the parts to fit either the nitro or e-version of revo and maxx. The difference is the spring.
  2. Replies
    6
    Views
    83

    It's an upgrade but not a very good one. Get the...

    It's an upgrade but not a very good one. Get the hot racing heavy duty slipper plate and hub and replace the slipper pads with a tmaxx 2.5 fiber brake disc. This has been reliable for me.
  3. Replies
    8
    Views
    174

    Those tiny little 6x12 pinion bearings are a...

    Those tiny little 6x12 pinion bearings are a considerable weak link in the diff design, with the 4 spider diff being second. Almost all 1/8 scale diffs use 8x16 bearings and a minimum of 6 spiders....
  4. Replies
    2
    Views
    40

    they are 6mm.

    they are 6mm.
  5. Replies
    7
    Views
    153

    I am currently experimenting with the Mugen...

    I am currently experimenting with the Mugen 1.6/9.75 springs at all four corners and using the threaded adjusters to tune it.
    Mugen rates the springs on wire thickness and coil wraps. 1.6 is the...
  6. Replies
    7
    Views
    153

    I installed 1/8 scale Mugen MBX6T rear shocks...

    I installed 1/8 scale Mugen MBX6T rear shocks (used FLM towers) at all four corners (one shock per wheel). You have to use steel CVD shafts to make the needed clearance but otherwise they install...
  7. Replies
    10
    Views
    233

    It was $90 and the center diff is from an ofna...

    It was $90 and the center diff is from an ofna hyper 7 TQ.
  8. Replies
    10
    Views
    233

    I had to put stiffer springs on the shocks but...

    I had to put stiffer springs on the shocks but from a dampening standpoint they are awesome. The truck absorbes rough surfaces like nothing.

    I bought the CD mount a few weeks back from RCM....
  9. Replies
    10
    Views
    233

    Mugen mbx6t truggy rear shocks at all four...

    Mugen mbx6t truggy rear shocks at all four corners with the Mugen buggy shock stand offs.
  10. Replies
    11
    Views
    155

    None of my tqi transmitters have the docking...

    None of my tqi transmitters have the docking station component.
  11. Replies
    11
    Views
    155

    I need to check the batteries. It very well could...

    I need to check the batteries. It very well could be the issue.

    I didn't know the firmware can be updated.
  12. Replies
    12
    Views
    231

    That's the ofna motor mount. It does not offer a...

    That's the ofna motor mount. It does not offer a lot of adjustability for different clutch bells but it will work with a pull start.

    I would also ditch the dual exhaust. Those are notorious for...
  13. Replies
    10
    Views
    233

    OK - I had an extra erevo radio box and mounted...

    OK - I had an extra erevo radio box and mounted it to the rear section of the chassis plate using some existing holes.
    ...
  14. Replies
    10
    Views
    233

    RCM Vmaxx Chassis Build

    So I took the leap and decided to replace my almost new FLM LCG chassis with the RCM vmaxx chassis. I really wanted to be able to do the 1/8 center diff. I was going to try and adapt the RCM...
  15. Replies
    11
    Views
    155

    LOL - i don't think so. It's not like i was...

    LOL - i don't think so. It's not like i was running a nitro vehicle at 5am.
  16. Replies
    2
    Views
    66

    it really isn't that hard to get the tranny out....

    it really isn't that hard to get the tranny out. pull the drive shaft pins and slide the ujoints off the output shafts, remove the 8 screws that are buried inside the chassis braces, pull the...
  17. Replies
    11
    Views
    155

    Runaway with a TQI radio?

    Today my ERBE ran away at 3/4 throttle (6s). Fortunately the wheels were turned to the right and the revo did a wide radius 4 wheel burnout like a drift car before smacking into my neighbor's garage...
  18. Replies
    24
    Views
    393

    yep - they are reinforcement rings to help keep...

    yep - they are reinforcement rings to help keep the pivot balls from popping out of place. Nitro and erevo carriers come with metal reinforcement rings to do the same thing. they are for the most...
  19. skid plates are expendable. they will get cracked...

    skid plates are expendable. they will get cracked and beat up through the normal course of use. i run my maxx at the track with some pretty bug jumps and never feel like it's out of it's element.
  20. Replies
    34
    Views
    444

    Oomp speaks the truth.

    Oomp speaks the truth.
  21. Replies
    34
    Views
    444

    just know that using the THS rear exit BB pipe...

    just know that using the THS rear exit BB pipe combined with the new era mount will cause some body fitment issues. You almost have to use the side pipe with that mount because the motor is canted so...
  22. Replies
    24
    Views
    393

    Oh and what wing mount is that? Tekno?

    Oh and what wing mount is that? Tekno?
  23. Replies
    24
    Views
    393

    Awesome. What's the performance difference...

    Awesome.
    What's the performance difference between a 2200kv motor and 1717kv motor? Is the 1717 needed due to the overall reduction in gear ratio from the center diff (12t pinion/52t diff)? Will you...
  24. Replies
    34
    Views
    444

    i wouldn't be too concerned about using a starter...

    i wouldn't be too concerned about using a starter box. The only way my revo can be started now is with the starter box. I bought the ofna t-start and it works perfectly - especially with the larger...
  25. Thread: Emaxx truggy?

    by rock-rod
    Replies
    35
    Views
    616

    That's also the chassis I currently have and its...

    That's also the chassis I currently have and its compatible with all the stock parts.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4