Search:

Type: Posts; User: gorilla2891

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. The above L shape plastic esc mount fits under...

    The above L shape plastic esc mount fits under body. I did same with thinner light aluminum. Aluminum because it helps heat sink.
  2. Replies
    12
    Views
    256

    Well documented that gearing is key. Also That...

    Well documented that gearing is key. Also That heatsinks and fans are too. I install on every rc I have. Less heat, even on a properly geared car, equals less resistance and wear. Also longer run...
  3. Replies
    25
    Views
    964

    I have a couple sets of goto go rc batts 3s and...

    I have a couple sets of goto go rc batts 3s and 2s. They out perform any battery hands down. A little more Spendy than average, but way better than Maxx amps. And durable. I have one 3s that is 6 yrs...
  4. Keep merv and improve it. Get a rally or boss and...

    Keep merv and improve it. Get a rally or boss and build it too. I have a merv, boss mustang built from parts and a summit crawler with tracks that has 1/10 yeti drive. It's nice that most parts are...
  5. Replies
    28
    Views
    595

    Use black rtv to seal diff. Liquid electrical...

    Use black rtv to seal diff. Liquid electrical tape to seal diff bulkhead.
  6. Replies
    6
    Views
    287

    Blk front tan rear. 80wt front 60wt rear. Done!...

    Blk front tan rear. 80wt front 60wt rear. Done! Get aluminum chassis braces from Toyz too. All good!
  7. Replies
    8
    Views
    296

    HR and Integy are good. I've used many of each on...

    HR and Integy are good. I've used many of each on all 3 of my 1/16 cars...
  8. Replies
    18
    Views
    400

    Shimming is needed, but not difficult. Stock oils...

    Shimming is needed, but not difficult. Stock oils work the best. Period. 50 front 30 rear. Clean and seal diffs with black rtv including bolts.
  9. Thread: Servo!!

    by gorilla2891
    Replies
    21
    Views
    417

    I put that savox in all 3 of my 1/16 cars. They...

    I put that savox in all 3 of my 1/16 cars. They are the best price, quality....
  10. Replies
    14
    Views
    457

    Yes, but it is for 2 nimh in series on flat hard...

    Yes, but it is for 2 nimh in series on flat hard surfaces the extra voltage gets you to 55+ the smaller gear helps take load off electrics. You can get 50 with stock gearing on 3s lipo.
  11. Replies
    1
    Views
    92

    ? pic? Pillow ball adjustment is out or something...

    ? pic? Pillow ball adjustment is out or something is broken...
  12. Replies
    14
    Views
    457

    3s is fine for the merve. It is the "speed"...

    3s is fine for the merve. It is the "speed" pinion that is only for pavement and flat surfaces...
  13. Replies
    14
    Views
    457

    I ran stock esc and gearing for years on 3s in...

    I ran stock esc and gearing for years on 3s in Charleston heat, with a heatsink/fan on motor. It is a good thing no matter what you do.
  14. I tried a center diff, i did not like it.... Your...

    I tried a center diff, i did not like it.... Your problem, pre center diff sounds like slipper adj, and, or rear diff losing fluid. You should pull, check, refill with 30wt, rtv mating surfaces and...
  15. Replies
    9
    Views
    217

    You will hear w whining noise from the slipper...

    You will hear w whining noise from the slipper when worn out when you hit the gas..
  16. Replies
    7
    Views
    604

    Front 50wt traxxas rear 30wt. But clean diffs and...

    Front 50wt traxxas rear 30wt. But clean diffs and seal mating surfaces and screw holes with rtv. otherwise diff fluid will leak out and no limited slip.... = spinouts when throttle is hit
  17. Replies
    7
    Views
    604

    Center diff is not needed. Proper oils in diffs...

    Center diff is not needed. Proper oils in diffs is better
  18. Replies
    3
    Views
    201

    Use the centerdiff and adjust the slipper. You...

    Use the centerdiff and adjust the slipper. You can keep the 4wd. 50k front and center, 30k rear?
  19. Replies
    32
    Views
    1,521

    Well, when one of those get bent you can... :)

    Well, when one of those get bent you can... :)
  20. Replies
    32
    Views
    1,521

    get the summit rear arms, 10mm extended and...

    get the summit rear arms, 10mm extended and Booyah!

    Side note, better handling...
  21. Replies
    83
    Views
    10,024

    WOW! Hobby room....:p~ what's in that fridge?...

    WOW! Hobby room....:p~

    what's in that fridge? :thumbup:
  22. Thread: $16

    by gorilla2891
    Replies
    9
    Views
    426

    Heatsink/fan for motor is a good investment.

    Heatsink/fan for motor is a good investment.
  23. Replies
    2
    Views
    144

    Traxxas wheelie bar? Remove rear bulkhead braces...

    Traxxas wheelie bar? Remove rear bulkhead braces and bolt in.. ? I have T bone set up so its been a while......
  24. Replies
    12
    Views
    587

    AWESOME! :thumbup:

    AWESOME! :thumbup:
  25. If you do not want ballooning, you have to buy...

    If you do not want ballooning, you have to buy tires and wheels separately. And tape the inside of tires with gorilla tape, before gluing.
Results 1 to 25 of 374
Page 1 of 15 1 2 3 4