Search:

Type: Posts; User: Jeephound79

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    10
    Views
    584

    I have tried it with the vehicle moving also. It...

    I have tried it with the vehicle moving also. It is almost as if the spring that runs from the servo to the shift lever isn't putting any tension on the lever at all.
  2. Replies
    10
    Views
    584

    transmition linkage

    I'm having an issue with my linkage. If I try to shift, the linkage will just twist in the shift leaver instead of pushing/pulling. Servo works great, just the goofy wire just twists in its hole. ...
  3. Replies
    7
    Views
    482

    Hehe that is no problem, it was just a matter of...

    Hehe that is no problem, it was just a matter of cleaning it before the wife woke up. Thanks everyone for the advice.
  4. Replies
    7
    Views
    482

    Just cut the holes in the tires and slung the...

    Just cut the holes in the tires and slung the water out....wish I would have done it outside though. Swamp mud water in a white sun room doesn't look right. Thanks Quadiak for the encouragement and...
  5. Replies
    7
    Views
    482

    Freaking out

    Alright, I'm nervous as all get out. I submerged my Summit for the first time today. Don't get me wrong. Loved it. But now I'm doing the after run on it and I'm realizing (remember, I'm a nitro...
  6. Replies
    11
    Views
    293

    Just sleve it. Nothing is cooler than getting...

    Just sleve it. Nothing is cooler than getting your hands greasy and seeing the entrails of your beast.
  7. Replies
    9
    Views
    352

    +1 on the LSN and clutch. I blew out 2 clutches...

    +1 on the LSN and clutch. I blew out 2 clutches with almost the same symptoms.
  8. What ever it is, just make sure you post pics.

    What ever it is, just make sure you post pics.
  9. Replies
    4
    Views
    226

    Well, once again I got bit in the butt with the...

    Well, once again I got bit in the butt with the old saying "you should have listened to you wife". When I put it all back together, she said "you put the back shocks in backwards" In my pov at that...
  10. Replies
    10
    Views
    910

    I always give it to "The Big T" when it comes...

    I always give it to "The Big T" when it comes down to PR and Customer Service. I had some minor querks with my Revo Platinum and they were sending parts left and right for no extra charge. I even...
  11. Replies
    5
    Views
    470

    You are asking for two compleatly different...

    You are asking for two compleatly different worlds. Speed and reliability aren't exactly compatible. If you are looking for a rock flinging, pavement burning, wheelie machine...then by all means,...
  12. Thread: Here I am

    by Jeephound79
    Replies
    3
    Views
    302

    Here I am

    Alright everyone. I'm usualy on the Revo pages, but just yesterday I took a Summit out of the box and let her see the Pennsylvania sun shine....then I promptly showed it the Pennsylvania mud and...
  13. Replies
    4
    Views
    226

    ride hight malfunction

    Good evening everyone. I just got done with my first shock rebuild in my 5304. I'm having an issue with the back end sagging lower than the front. The rear is also having an issue with limited...
  14. Replies
    7
    Views
    273

    It hit 52 here this past weekend and I got to put...

    It hit 52 here this past weekend and I got to put 500ml through it
  15. I own the Spektrum DX3, I have no complaints...

    I own the Spektrum DX3, I have no complaints about it. I got the extra Rx (put it in my AX-10)and the two servos also (the High Torque Z590 also went to the AX-10. Wife says that I have to blow it...
  16. Replies
    7
    Views
    223

    Got if off, thanks guys. If it wasn't for you...

    Got if off, thanks guys. If it wasn't for you all out there, I would probably never get anything off.
  17. Thread: Vspec Help

    by Jeephound79
    Replies
    9
    Views
    184

    +1 on the WD 40 and heat gun.

    +1 on the WD 40 and heat gun.
  18. Replies
    15
    Views
    334

    two weeks is a long time. I would contact them...

    two weeks is a long time. I would contact them and ask them if there is an issue. It might be on back order. The longest anything took for me to get was a week and that was because of my address...
  19. Replies
    19
    Views
    570

    I'll wait for a month to get a beetle body and a...

    I'll wait for a month to get a beetle body and a hat. What's the catch?
  20. Replies
    7
    Views
    223

    I'm removing it because the one that is currently...

    I'm removing it because the one that is currently on it threw a pin through the bell and into my spur. I'm putting a new one on.
  21. Replies
    12
    Views
    493

    Yep, that's a Revo alright. I know one when I...

    Yep, that's a Revo alright. I know one when I see one, and that sir, is a Revo
  22. Thread: servos

    by Jeephound79
    Replies
    7
    Views
    273

    I am ruing the day when my stering goes out. If...

    I am ruing the day when my stering goes out. If I don't catch it right away, that second servo is going to have a **** of a work out and KO shortly after the first
  23. +1 for breaking it in. Wrap the head in aluminum...

    +1 for breaking it in. Wrap the head in aluminum foil and put a baby sock over it. WATCH YOUR TEMPS. If the temp drops to low, the engin won't break in. If it gets to hot, your engin will just...
  24. Replies
    7
    Views
    223

    That is what I've tride so far. I'm wondering if...

    That is what I've tride so far. I'm wondering if they thread locked it
  25. Thread: help

    by Jeephound79
    Replies
    12
    Views
    270

    Nah, don't get a pull start, get a bump start. ...

    Nah, don't get a pull start, get a bump start. Less rotating mass and it doesn't kill your arm.
Results 1 to 25 of 89
Page 1 of 4 1 2 3 4