Search:

Type: Posts; User: pumpkin13

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    226

    snook thanks for the info. it'd be nice if the...

    snook thanks for the info. it'd be nice if the dealer could have told me this.
  2. Replies
    2
    Views
    226

    a arms for tmaxx classic

    ok, so I just found out the "short" radius a arms are no longer available and that's fine. so, I went to my local HOBBYTOWN USA and bought the bulkheads and a arms that are listed on the TRAXXAS...
  3. Replies
    1
    Views
    88

    drivetrain upgrade

    well, got this new motor running pretty well (but not perfect) and have destroyed some output yolks on my classic. wondering if the 3.3 components will bolt right in?? I.E. output yolks, halfshafts,...
  4. Replies
    16
    Views
    483

    os .18 cv rx appears to be a bust. looking for...

    os .18 cv rx appears to be a bust. looking for wheelies...not even close. everything else being the same, the old picco .12 will run with it. been tuning and tuning and tuning on this thing and top...
  5. Replies
    5
    Views
    210

    had this problem with a pull start. sometimes...

    had this problem with a pull start. sometimes would grab sometimes felt like it was slipping. pulled that little shaft out of the back of the motor (owb??) and scratched it up with some 400 grit...
  6. if you never ceased the motor it's just gunked...

    if you never ceased the motor it's just gunked up... let it soak and be patient.
  7. not sure about the mineral spirits but IDK. as...

    not sure about the mineral spirits but IDK. as far as I know denatured alcohol is called just that. there is also a product we use in the refineries a lot to loosen frozen bolts called Kroil and...
  8. you don't have to take it all apart for it to...

    you don't have to take it all apart for it to run, but for it to run and last it's the best bet. x2 on the penetrating oil, too or atleast the denatured alchohol seems to cut through the glue that...
  9. p.s. by crank nut I mean the back side of the...

    p.s. by crank nut I mean the back side of the motor with the ez start off. mine was an 8mm I believe.
  10. I just went through this with my .15 engine. ...

    I just went through this with my .15 engine. submerged the entire engine in DENATURED alcohol for a few days and then turned the crank nut with a 4" adjustable prob. with about 10-15 ft. lbs. of...
  11. Replies
    0
    Views
    509

    good parking lots in SE pennsy

    my tmaxx should be back together soon (new engine) and I'm looking for a good wide open space to go break it in and do some speed runs later on. wondering if anyone in the area had any good places...
  12. Replies
    5
    Views
    566

    so chickenman, you have the pipe pictured in...

    so chickenman, you have the pipe pictured in nitro trout's post or the traxxas pipe? I'm currently running an old picco .12 motor and for what it is has great power and acceleration with that pipe...
  13. Replies
    5
    Views
    566

    best exhaust for os 18 cv rx

    okay, upon the advice of this forum I decided to go with the os .18 cv rx in my classic tmaxx. everything on the truck is stock except the servos and chassis. I currently am running an aftermarket...
  14. I am in a similar boat but not exactly. Mine sat...

    I am in a similar boat but not exactly. Mine sat for 8 years and when I went to get it going again it didn't want to shift so I was hesitant to take the trans apart to clean it. If you follow the...
  15. Replies
    16
    Views
    483

    Well, may have just screwed up. ordered the OS...

    Well, may have just screwed up. ordered the OS .18 CV RX, not the CV RX (S). Do I need to cancel this and get the "S"? I assume the s stands for Short crankshaft?
  16. Replies
    16
    Views
    483

    rb, just checked out this engine and it even has...

    rb, just checked out this engine and it even has the rotary carb; looks like this is where I'm headed. Will the factory clutch bell, exhaust manifold, and engine mount work with this motor? If so,...
  17. Replies
    16
    Views
    483

    well, can't figure out how to post pics on here. ...

    well, can't figure out how to post pics on here. so, after a little consideration and the lack of availability of the right engine I think I'm just gonna go with the 3.3 conversion and change out...
  18. Replies
    16
    Views
    483

    well thanks for all the input so far; it...

    well thanks for all the input so far; it definitely helps having more information. unfortunately, seems like all the good, direct replacement engines with the rotary carb are no longer in production....
  19. Replies
    16
    Views
    483

    is the sirio a direct replacement of the original?

    is the sirio a direct replacement of the original?
  20. Replies
    16
    Views
    483

    well, I'm not 100% fixed on either. I'm flexible...

    well, I'm not 100% fixed on either. I'm flexible as long as the costs are not outrageous. I'm really trying to find the perfect fit; something that will pull wheelies but not destroy the trans or...
  21. Replies
    16
    Views
    483

    motor identification???

    hi everybody, new to this forum but not entirely new to this tmaxx. bought it in '01 (classic) and somewhere around 02 or 03 upgraded to a trinity/picco .12engine. all I can say is it was a direct...
Results 1 to 21 of 21