Search:

Type: Posts; User: jsdcs07

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    229

    I have the same charger and it has the same...

    I have the same charger and it has the same problem. To store I put in on a low charge rate and watch the voltage. When it gets a little over 3.8 I turn it off. Don

    this is more and less what i am...
  2. Replies
    3
    Views
    229

    Store charging help.

    hi, I am trying to story charge me bat's, on a i maxx b6 charger, as not had the chance to use them from fully charged, When i discharge at 1amp only takes a few min and sits at 3.80, However when i...
  3. Replies
    17
    Views
    553

    that I will have been dispatched so should be...

    that I will have been dispatched so should be with me soon
  4. Replies
    17
    Views
    553

    http://www.wheelspinmodels.co.uk/i/207916/

    http://www.wheelspinmodels.co.uk/i/207916/
  5. Replies
    17
    Views
    553

    fastrex ones

    fastrex ones
  6. Replies
    17
    Views
    553

    Update for you all. Today i have bourght any...

    Update for you all.

    Today i have bourght any upgraded steel front and rear drive shafts, OUCH for a basher that cost.

    As far as the hex will do what i can with dreamal.
  7. Replies
    17
    Views
    553

    Yes that is what i am talking about. It is...

    Yes that is what i am talking about. It is twisting and and destroying the output where the pins go.

    http://i650.photobucket.com/albums/uu230/jsdcs07/images_zpsfb961f78.jpg

    Looking like this. ...
  8. Replies
    17
    Views
    553

    Slipper, i have tried to loosen but get lots of...

    Slipper, i have tried to loosen but get lots of slipping, to the point that now get very little wheel spin
  9. Replies
    17
    Views
    553

    broken parts and striped hex

    After some help.
    Firstly I have a few striped Hex heads and really sturgling to remove these and suggestion?
    Secondly, I keep killing the read drive shafts, the out put for the diff bit, any...
  10. Replies
    10
    Views
    976

    i think that the most parts needed will be, ...

    i think that the most parts needed will be,
    Motors, Motors, Motors, Motors, Motors, Motors, Motors, Motors and some more Motors
  11. Replies
    15
    Views
    649

    Might be a long short, But i have a simlar...

    Might be a long short, But i have a simlar problem,

    when all 4 wheels are off the ground the front 2 and left rear all spin freely, The right does not, usless use the diff lock,

    I have looked...
  12. Thread: steering

    by jsdcs07
    Replies
    7
    Views
    459

    all i have done is plug in to the reciver, and...

    all i have done is plug in to the reciver, and still stock servo horn, and saver, it is working very nicely, no problem (apart from wear and tear) which i expect
  13. Thread: steering

    by jsdcs07
    Replies
    7
    Views
    459

    I do a lot of Trailing and crawling only use 1 X...

    I do a lot of Trailing and crawling only use 1 X savox sw1210sg, which is 20Kg and waterproof, I find it deal with the a heavy beadLoc wheel. works very well and have no need to have 2 of these on...
  14. Replies
    4
    Views
    244

    that looks normal, Mine also looks like that

    that looks normal, Mine also looks like that
  15. Thread: Flip recovery

    by jsdcs07
    Replies
    4
    Views
    371

    Flip recovery

    My Alias seem to be a bit wobbly now after a flip, Aslo seem to be loosing loads of high about 4 - 6 foot when recovering from a flip.

    was not all ways like this but seem to of devloped in the...
  16. Thread: Old to New

    by jsdcs07
    Replies
    5
    Views
    148

    Hi, the old rustler is coming on now. Gearing...

    Hi, the old rustler is coming on now.

    Gearing question,

    I am runing 8.2 nihm with 25 / 84 but was very hot motor, but after looking at new style set up is 25 / 83, Will that one tooth on the...
  17. Thread: Gearing?

    by jsdcs07
    Replies
    1
    Views
    127

    Gearing?

    I put stampede 4x4 tyres on the slash, as like the ground clearance.

    I am running 2C lipo with the stock VXL and 13 / 54 set up but the motor and esc is getting vary hot, Looking at going 11 / 54...
  18. Thread: Old to New

    by jsdcs07
    Replies
    5
    Views
    148

    Well I was going with the new slipper but then...

    Well I was going with the new slipper but then realised that I would need entire new part for it. Coz this is on a budget I am trying to keep it and low costing as possible.
    She coming back to life...
  19. Thread: Old to New

    by jsdcs07
    Replies
    5
    Views
    148

    Old to New

    I have recently got my hand on my old Rustler, I think I got this back in 1995 or something like that, Have the old rubber style slipper clutch on her.
    I am bring her back to life again after a...
  20. Replies
    15
    Views
    726

    Wind, ha ha, there another thing that i am...

    Wind, ha ha, there another thing that i am getting to girps with, when hovering i and the wind get it, the alias handles it really well, but you have to ease off the power and it really lift up then,...
  21. Replies
    15
    Views
    726

    thank, i think that the reason i noticed it was...

    thank, i think that the reason i noticed it was coz i have always used it in beginner mode which does not act the same. as i was in Exp (fast ) mode which was why i noticed it. bigger error. but and...
  22. Replies
    15
    Views
    726

    so you are saying as i push forward increase the...

    so you are saying as i push forward increase the engine speed to keep level. (i know i might be being think here)
    so if hovering at 50% throttle, increase to 80% as i go forwards

    this is normal...
  23. Replies
    15
    Views
    726

    Yes Lose altitude, when i acceleration

    Yes Lose altitude, when i acceleration
  24. Replies
    15
    Views
    726

    Getting better at flying

    Hello fellow Alias owners.
    Just thought I would say hello, I have never really had much as far as flying RC goes, a few Plaines (which died) bad crashed, and in doors small helicopters. So I was a...
  25. Replies
    12
    Views
    330

    Mine does this so what i do is unplug the bat,...

    Mine does this so what i do is unplug the bat, Motor connectors, Reconnect all and seams fine afterwards.
Results 1 to 25 of 330
Page 1 of 14 1 2 3 4