Search:

Type: Posts; User: Kahabut

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    775

    Having literally just done a new clutch... can...

    Having literally just done a new clutch... can someone tell me how you generally go about putting that spring on there?

    I tried a couple different things, and then just ended up hooking it, and...
  2. Replies
    6
    Views
    684

    YES, you can use your other radio. BUT FIRST......

    YES, you can use your other radio. BUT FIRST... where the micro servo connects to the tranny, by a rod... pin that rod in place so that an accidental impact doesn't shift your truck.

    Otherwise,...
  3. Replies
    59
    Views
    2,456

    Does it still work fine in reverse? Then your...

    Does it still work fine in reverse? Then your transmission is stuck in second gear. Move the adjuster towards " Shift sooner" which I recall as being full left. Full left should stick the trans...
  4. Replies
    59
    Views
    2,456

    You say you checked the reverse servo? When it...

    You say you checked the reverse servo? When it moves, it pulls a little pin in or out of the transmission. So switch it, and wait just a second after it stops moving, and give it a little blip on...
  5. Replies
    2
    Views
    351

    Check the orientation of the fuel lines. Are...

    Check the orientation of the fuel lines. Are they parallel to the ground? The thing is, it's a gravity/pressure feed system, so when you roll the truck, if the fuel lines aren't flat in relation to...
  6. Thread: 2.5r problems

    by Kahabut
    Replies
    10
    Views
    537

    OK, I have slightly different opinion about your...

    OK, I have slightly different opinion about your problem.
    First, pull off the clutch and look at it closely. Are the shoes ok? Is it all round when you put it together? Is the spring in good...
  7. Oh yeah, if you like grinding stuff, you can go...

    Oh yeah, if you like grinding stuff, you can go this way too. I'm not a fan personally, but that's because I'm not so good with a moto tool.
  8. Alright, so I just did this for two revo 3.3s. ...

    Alright, so I just did this for two revo 3.3s. The Ofna Box you want is called T-start. You'll need a couple of 7.2v battery packs. I assume you have that covered.
    As for the truck itself, you...
  9. Replies
    8
    Views
    2,199

    pbflash - I have the same... issue. I have the...

    pbflash - I have the same... issue. I have the FOC and Center Diff and can't make my revo wheelie at all. But since it breaks 50mph (clocked by police radar - they thought it was the best toy they...
  10. Thread: Holy Crap!!

    by Kahabut
    Replies
    16
    Views
    1,083

    I converted both my revo trucks to bump start. ...

    I converted both my revo trucks to bump start. Ofna makes a bump box called the "t-start" specifically for Revo. No modification of the truck is required. Well, other than ripping off the...
  11. Replies
    3
    Views
    473

    You can pretty easily 'prime' the engine by...

    You can pretty easily 'prime' the engine by holding your finger over the exhaust outlet for a second or two while you crank the engine. This should get your fuel system ready to start without having...
  12. Replies
    12
    Views
    894

    I had a very similar problem recently. There was...

    I had a very similar problem recently. There was nothing wrong with the servo, it's just that the traxxas throttle horn pivot is a bit dubious. I found a couple of solutions.

    First, be 100%...
  13. Replies
    11
    Views
    689

    Is that motor and kit compatible with Bump Start...

    Is that motor and kit compatible with Bump Start box? Because I really like my bump starter and I don't want to move away from it.
  14. Replies
    11
    Views
    689

    1) OK, I figured it out. Fortunately before I...

    1) OK, I figured it out. Fortunately before I tore apart the drive system. It turns out my cheap as ... well cheap wheels broke. The right rear hex hub is completely stripped out and the axle...
  15. Replies
    2
    Views
    424

    Nice video, nicely done. After some of the crazy...

    Nice video, nicely done. After some of the crazy things I've seen on youtube for bearing removal/replacement, this video is all anyone should watch.

    I do have one question... how long was the...
  16. Replies
    11
    Views
    689

    New To Revo - Some questions

    First, my story. I recently purchased two Revo 3.3's on Ebay. Got a good deal on the trucks and a pile of spare parts. I've been tuning, replacing, tearing down and rebuilding since then.

    The...
Results 1 to 16 of 17