Search:

Type: Posts; User: pntmachine

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    117

    That is not my truck, that is Steve Slaydens so...

    That is not my truck, that is Steve Slaydens so you will have to go by what you are seeing in the photos. Sorry
  2. Replies
    28
    Views
    596

    The wings I always used were the JConcepts. The...

    The wings I always used were the JConcepts. The body was always a JConcepts.
    http://i181.photobucket.com/albums/x194/pntmachine/100_4057-1.jpg...
  3. Replies
    28
    Views
    596

    This is what I used racing. I installed a charge...

    This is what I used racing. I installed a charge jack off an old box so I didn't have to keep opening the box to charge.
    http://i181.photobucket.com/albums/x194/pntmachine/DSC00372.jpg...
  4. Replies
    3
    Views
    117

    With some cutting and trimming it will work....

    With some cutting and trimming it will work.
    http://i181.photobucket.com/albums/x194/pntmachine/DSC00915-1.jpg
    http://i181.photobucket.com/albums/x194/pntmachine/DSC00894.jpg
  5. Replies
    6
    Views
    228

    We always said at the track caster is faster....

    We always said at the track caster is faster. Rock Rod is right depending on what you are doing. I always ground some material of the fronts of the a arms to allow 5 clips and sometimes 6.
  6. Replies
    1
    Views
    119

    Usually the pushrod ends were not much of an...

    Usually the pushrod ends were not much of an issue. Lunsford rods have a longer and deeper cut thread than stock so they held up pretty good. Shock rod ends we would always replace with Racers Edge...
  7. Replies
    6
    Views
    252

    Buy a new block with bearings off ebay and change...

    Buy a new block with bearings off ebay and change over to that. Problem will be solved. Bearings are bad most likely. Keep going and crank will drift and park itself on casing which will destroy the...
  8. Wow this may take some memory which I am growing...

    Wow this may take some memory which I am growing shorter of. The wings are Jconcepts. The wheels and tires on the Revo are Losi's and I believe came stock on the MBX5T. Very similar to crimefighters...
  9. .............

    .............
  10. Replies
    7
    Views
    269

    Double G is right, hardened spur needs a hardened...

    Double G is right, hardened spur needs a hardened bell. Philly is also correct, chassis flex is usually a number one cause of stripped spurs. That's why the teeth always look unevenly ground off or...
  11. Replies
    9
    Views
    372

    Check also to see if the screw pin is sheared on...

    Check also to see if the screw pin is sheared on the primary shaft.
  12. I ran a Qoncept as well as the M2C. Not sure if...

    I ran a Qoncept as well as the M2C. Not sure if just the qoncept will be enough to control all the chassis flex but I do think it works well....
  13. Replies
    15
    Views
    214

    Body on with side pipe....

    Body on with side pipe.
    http://i181.photobucket.com/albums/x194/pntmachine/DSC00027-1.jpg
    http://i181.photobucket.com/albums/x194/pntmachine/rc_pro_series_03_30_2008_520.jpg
  14. Replies
    15
    Views
    214

    What's up k, those were the good ole days!! lol I...

    What's up k, those were the good ole days!! lol I miss em.
  15. Replies
    15
    Views
    214

    That's the same set up I used as well back then. ...

    That's the same set up I used as well back then.
    http://i181.photobucket.com/albums/x194/pntmachine/071807_17341-1.jpg
    http://i181.photobucket.com/albums/x194/pntmachine/100_4071.jpg
  16. Traxxas upgraded there rear bearings in the newer...

    Traxxas upgraded there rear bearings in the newer engines. If you buy a boxed replacement you want to get the ones with the box that has a yellow seal that says championship engines on it.
  17. Replies
    14
    Views
    764

    That is not from a wreck that is torque twist. It...

    That is not from a wreck that is torque twist. It happens to us a lot in racing especially here in Florida where we run mostly blue groove or high bite tracks. Only choice is to replace them. They...
  18. I don't think there is anything you will gain...

    I don't think there is anything you will gain from turning the pillow balls. With as much as can be taken off the ackerman done and stops removed there is no more travel left even if the balls were...
  19. I have raced RD carriers for years and they are...

    I have raced RD carriers for years and they are already have more travel than any carrier produced. Mine turns rack to rack with no problems and are already bevel cut in that area. They have as much...
  20. Replies
    3
    Views
    227

    You are going to be fine. 240 is not that hot,...

    You are going to be fine. 240 is not that hot, 280 and up is.
  21. Replies
    18
    Views
    614

    It may be flooding out. Return it to factory...

    It may be flooding out. Return it to factory settings as said. If it is a broken in motor take the high speed to about 3 and 1/2 turns. Then lean the bottom a little at a time until it pops and fires...
  22. Replies
    12
    Views
    2,158

    The extended chassis is just the stock 3.3...

    The extended chassis is just the stock 3.3 chassis and nothing else. That term was actually from the early days when we were racing the 2.5 chassis. They were extending that chassis then and it just...
  23. Check the output shaft pin in the forward gear....

    Check the output shaft pin in the forward gear. Sometimes it snaps inside and cannot be seen when you just look inside the tranny.
  24. Replies
    10
    Views
    1,354

    You may have sheared the pin in the forward gear...

    You may have sheared the pin in the forward gear of the output shaft.
  25. On adjustment to the servos on a dual setup the...

    On adjustment to the servos on a dual setup the servos do not end up at rest being at 90 degrees, they both should end up off center slightly.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4