Search:

Type: Posts; User: Greywerld

Page 1 of 18 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    177

    High tranny RPMs are what cause the shift to take...

    High tranny RPMs are what cause the shift to take place.
    http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXHGF7&P=7
    If you look at the gears in the link you'll see two pins on the gear to the...
  2. Replies
    16
    Views
    283

    Seeing the way that sheared, you may also want to...

    Seeing the way that sheared, you may also want to check the bearings at both ends of the driveshaft. Something bound up for it to snap like that.
    If you don't put oil or grease or something to...
  3. Replies
    14
    Views
    389

    Everything I can find shows that the lcg kit just...

    Everything I can find shows that the lcg kit just uses the stock bellcranks, so if that fits in place of a stock bellcrank it should fit the lcg.
    I don't know if anyone else here has used that set,...
  4. Replies
    3
    Views
    139

    Start with the basics, what is the condition of...

    Start with the basics, what is the condition of the spur gear and clutch bell?
    When it is running, are both spinning?
  5. Replies
    3
    Views
    195

    No, its just that with the wider wheels from the...

    No, its just that with the wider wheels from the rustler and the slash's wide body that as the wheels pivot when steering they can snag the edges of the body around the tires. You could trim the...
  6. Replies
    3
    Views
    195

    My brother has a Rustler and and we tried...

    My brother has a Rustler and and we tried swapping wheels. The rear wheels won't be a problem, but the front seemed to catch the body in turns.
  7. Thread: help please

    by Greywerld
    Replies
    7
    Views
    184

    You may want to look into RPM a arms as well....

    You may want to look into RPM a arms as well.
    http://www3.towerhobbies.com/cgi-bin/wti0095p?FVPROFIL=&FVSEARCH=%3Cb%3Erpm%3C%2Fb%3E+a-arms+%3Cb%3Erevo%3C%2Fb%3E
    That will give you a list of several...
  8. Thread: Servo Noise

    by Greywerld
    Replies
    3
    Views
    181

    Are you running with Optidrive? If so, unplug...

    Are you running with Optidrive? If so, unplug the throttle servo from the Optidrive module and plug it directly into the receiver and see if it still starts buzzing. You'll need to unplug the...
  9. Replies
    7
    Views
    282

    Lot of people are using the Losi 3.4 carburetor...

    Lot of people are using the Losi 3.4 carburetor to get more performance out of the 3.3.
    You can also upgrade a few suspension components from steel to aluminum like outlined at the end of this Pit...
  10. Never said you were a noob, but outlining the...

    Never said you were a noob, but outlining the troubleshooting process helps in a few ways:
    1. It may remind you of something you may have missed.
    2. It helps others who may read this thread in...
  11. Check for servo movement first, then try pulling...

    Check for servo movement first, then try pulling the rod going into the transmission in and out by hand.
    If the servo isn't moving, unplug it from the opti-drive and plug it directly into the...
  12. Replies
    2
    Views
    136

    Start by checking the arms and the bulkheads for...

    Start by checking the arms and the bulkheads for cracks and broken bits. If they aren't broken, pull the hinge pins and inspect them.
    Pics or video may help in diagnosing the problem.
  13. Replies
    6
    Views
    216

    The general idea being that you want the smallest...

    The general idea being that you want the smallest clutch bell and the largest spur, but you sacrifice speed. If you want to go for lower gearing, you can use Jato clutch bells and spurs as outlined...
  14. Replies
    13
    Views
    502

    I don't know, I picked up a set of STRC knuckles...

    I don't know, I picked up a set of STRC knuckles for my Slash and they had all kinds of slop around the bearings. I could move the bearings 2-3 mm up and down in the knuckle. Pull it apart and...
  15. Replies
    11
    Views
    481

    You should be able to remove the shafts without...

    You should be able to remove the shafts without removing more than skidplates. To get the differential out, you need to remove the bulkhead from the chassis. Screws on top holding the bulkhead to...
  16. Replies
    6
    Views
    305

    The engine mounting point on the chassis is...

    The engine mounting point on the chassis is notorious for bending, even with the reinforcing bracket. Check that before putting a metal spur on.
  17. Replies
    11
    Views
    481

    Looks like something is bound up in either the...

    Looks like something is bound up in either the tranny or drive train. Start by pulling a drive line off the transmission (front or rear) and the differential. Essentially making it a 2wd, and see...
  18. Replies
    11
    Views
    961

    Talking with folks at LHS, they told me that...

    Talking with folks at LHS, they told me that whenever a traxxas nitro truck comes in with ezstart issues the first thing they do is try it with a glow igniter on the plug and the wand turning over...
  19. Replies
    11
    Views
    961

    Probably be doing it myself after I get my hands...

    Probably be doing it myself after I get my hands on a glow-igniter.
  20. Thread: tires

    by Greywerld
    Replies
    2
    Views
    746

    There's also these:...

    There's also these:
    http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXBFXF&P=7
    My brother has run the smaller road rage tires on the rear axle of his rustler and likes them for street/sidewalk...
  21. Chassis length was longer on the 3.3 revos. The...

    Chassis length was longer on the 3.3 revos. The 2.5 had a shorter chassis, from what I've seen in other threads the extra length was added in the front end of the chassis. If your front shock mount...
  22. Yep, definitely the old 5309. I believe the new...

    Yep, definitely the old 5309. I believe the new one also had the waterproof servos, two-stage air filter, and chrome muffler.
  23. Replies
    13
    Views
    1,420

    I think it is a matter of taste and what specific...

    I think it is a matter of taste and what specific part. I have integy skids on my revo and haven't had a problem, other than wishing I had bought the silver instead of the blue (all the scrapes...
  24. Replies
    3
    Views
    1,175

    My understanding is that the main difference...

    My understanding is that the main difference between the t-maxx tranny and the revo tranny is the case. The inner gears and shafts are identical. Check exploded views for the t-maxx tranny and the...
  25. Replies
    8
    Views
    1,447

    Sorry Duxx, I haven't had a chance to run the...

    Sorry Duxx, I haven't had a chance to run the truck with 'em yet. I just got 3 inches of snow here, and work keeps me out of town for a week at a time. I'm getting things charged up and set to give...
Results 1 to 25 of 430
Page 1 of 18 1 2 3 4