Search:

Type: Posts; User: boilo56

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. I would go with LEM!

    I would go with LEM!
  2. Thread: summit issues?

    by boilo56
    Replies
    5
    Views
    272

    It looks like you have a weak BEC, or a bad...

    It looks like you have a weak BEC, or a bad servo. Test all the servos one by one, and see if there is one that is bad. If all of them are ok, you may need an external BEC. The problem should go with...
  3. Replies
    19
    Views
    1,221

    Man, you boat is awesome!!! I really liked it!...

    Man, you boat is awesome!!! I really liked it! Keep up the good work!
  4. Hi, first, i would check for any binding on the...

    Hi, first, i would check for any binding on the locking mecanism rods(wire pushing against it). Secondly, i would disconnect the rods from the horn of the T-lock and check if it move easelly, while...
  5. Thread: My FPV Summit

    by boilo56
    Replies
    857
    Views
    118,506

    cant see the vid!

    cant see the vid!
  6. Replies
    2
    Views
    313

    I think they will fit, but the look...

    I think they will fit, but the look...
  7. Thread: Dual 550s

    by boilo56
    Replies
    5
    Views
    400

    not slower, you can gear it up way more. i have a...

    not slower, you can gear it up way more. i have a twin-V merv, and the gearing is off the chart.
  8. Replies
    16
    Views
    507

    Hi, the only thnigs you'll need for spare parts...

    Hi, the only thnigs you'll need for spare parts is: A-arms, full set of bearings for the summit, maybe front and rear bumpers and mounts, and some spurgears! This truck almost bulletproof!!!
  9. Replies
    60
    Views
    4,880

    #57 here my winter beast!...

    #57 here my winter beast!
    http://pic20.picturetrail.com/VOL1324/13572864/24298419/409540377.jpg
  10. Replies
    4
    Views
    430

    Hi chris, yes you are right. This is how to do it!

    Hi chris, yes you are right. This is how to do it!
  11. Replies
    11
    Views
    501

    the chager can charge both, standard and new...

    the chager can charge both, standard and new traxxas lipos.
  12. Thread: 4s battery

    by boilo56
    Replies
    16
    Views
    590

    The only way i could see it work, is by adding an...

    The only way i could see it work, is by adding an external BEC... My 2cents. But im not even sure it wont toast the ESC... i think the ECS is made of two ESC connected internally in serie to provide...
  13. Thread: any thoughts?

    by boilo56
    Replies
    19
    Views
    518

    I would say motor size! 2200kv will spin the...

    I would say motor size! 2200kv will spin the wheel on the first trigger shot... 2650 have less torque, less clutch slipping more traction and less slipping. i have the tekin T81550kv/rx8 gen2 combo...
  14. Replies
    9
    Views
    571

    You might have a worn bearing in the front of...

    You might have a worn bearing in the front of your truck... that causes one frontwheel to rotate faster that the other... that could be the cause of the pulling to one side.
  15. Replies
    146
    Views
    12,090

    Hi everyone, this is the first part of the...

    Hi everyone, this is the first part of the snowblower...! FPV...
  16. Replies
    11
    Views
    650

    It happenned to me, it was the motor mount that...

    It happenned to me, it was the motor mount that wasn't aling properly. You can also check for the tranny bearings, maybe one is worn out.
  17. Replies
    7
    Views
    503

    Go take a look at my...

    Go take a look at my thread:http://traxxas.com/forums/showthread.php?8999354-My-summit-snow-plow you might find something there!
  18. Replies
    3
    Views
    554

    The tracks sucks! I would suggest Traxxas steel...

    The tracks sucks! I would suggest Traxxas steel center CVDs, Harden steel pinion and spur gear, UPGRADED slipper cluch, stiffer shocksprings, LEM Tranny upgrade(when avialable), LEM diff kit... And i...
  19. Thank you very much!

    Thank you very much!
  20. Well, if somebody have a link to those bore...

    Well, if somebody have a link to those bore reducer, i would really apreciate! Thanks!
  21. You better have a verrrry goood arm, li live in...

    You better have a verrrry goood arm, li live in Quebec, Canada, so, pretty far!:lol:
  22. Sorry to say, but i need a 5mm motor shaft... but...

    Sorry to say, but i need a 5mm motor shaft... but thanks for the effort!
  23. nevermind, i was able to make one! Thanks for the...

    nevermind, i was able to make one! Thanks for the idea!
  24. do you have a link, please?

    do you have a link, please?
  25. Just tried it, they don't ship to Canada.:(

    Just tried it, they don't ship to Canada.:(
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4