Search:

Type: Posts; User: Mr Durden

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    325

    Temp sensors are pretty tough!

    I haven't run my revo in almost a month, the weather out here has been kinda cool. Well today I was doing laundry and I pulled out a pair of shorts to wear so I could wash all my pants... I felt...
  2. Replies
    2
    Views
    219

    Disintegrating slipper clutch pads?

    I noticed my slipper clutch wasn't grabbing very well at all, and had a closer look. Turned out two of the pads were missing chunks out of them, and the third was completely missing. Anyone else...
  3. Replies
    19
    Views
    615

    My friend and I both bought ours in Calgary. He...

    My friend and I both bought ours in Calgary. He got his from PM Hobbycraft which is on 32nd ave NE, and I got mine from Action Hobby, down on Ogden Trail in the SE. So far the guys from PM have...
  4. Replies
    5
    Views
    414

    Re: stripped?

    That's kinda what I did, although I was afraid to put crazy glue right into the threads. I just coated the outside or the brass piece until it was airtight. This worked for quite a while but I...
  5. Replies
    6
    Views
    701

    YES!!! That was the problem! The glowplug was...

    YES!!! That was the problem! The glowplug was bunk. I'm near positive it was goofing up ever since I put it in now that I think about it. It's been down for repairs because my HSN stripped out,...
  6. Replies
    8
    Views
    456

    My 120mm bottoms out way too easy too, and sags...

    My 120mm bottoms out way too easy too, and sags quite bad in the back. I'm going to try different oil in the shocks and see if it helps.
  7. Replies
    6
    Views
    701

    Yeah, obviously I made sure it was tight :p I'll...

    Yeah, obviously I made sure it was tight :p I'll try a new plug right now and see how it goes.
  8. Replies
    6
    Views
    701

    Bubbles from glowplug hole

    My Revo has been running horrible lately... if at all. I think I finally pinned it down today when I noticed that when I crank the motor over, there are bubbles coming out of around the glowplug. I...
  9. That's what I figured, since I couldn't explain...

    That's what I figured, since I couldn't explain it any other way. Oh well, I had to learn how to rebuild one of these sooner or later :o
  10. Replies
    53
    Views
    3,048

    Wow! How much stuff did you break???

    Wow! How much stuff did you break???
  11. Sounds very simmaller to my problem, but not...

    Sounds very simmaller to my problem, but not quite. Mine will start fine, but almost always will not idle. I can give it medium throttle, and it'll go fine. If I give it full throttle it'll die. ...
  12. Replies
    18
    Views
    1,149

    I run in Calgary and I never wheelied until I...

    I run in Calgary and I never wheelied until I raised the ride hieght.
  13. Replies
    12
    Views
    1,792

    My HSN stripped on it's own without turning it...

    My HSN stripped on it's own without turning it much at all as well. My new carb is on the way, but for now I've sealed it with super glue.

    If you got into this hobby without understanding that...
  14. Replies
    27
    Views
    1,093

    I think that if you don't have access to stuff to...

    I think that if you don't have access to stuff to cut wood with, just stick with dirt jumps. They're easier to mess with anyhow, you can change the pitch and kick of it really easy that way.
  15. Replies
    6
    Views
    398

    shouldn't they read the same? Maybe one is using...

    shouldn't they read the same? Maybe one is using psi, and the other shows kpa?
  16. I don't live with my parents, so I don't plan on...

    I don't live with my parents, so I don't plan on telling them at all :o My girlfriend made fun of me though, said I was a little kid :(
  17. Replies
    7
    Views
    490

    So I should stock up on driveshafts eh? :o How...

    So I should stock up on driveshafts eh? :o How thick of oil should I use to do that then? Maybe I'll just use maple syrup ;)


    Yeah, I know I'll lose some turning radius... that's why I only...
  18. Replies
    43
    Views
    1,667

    update: Currently my hsn stripped out of my carb...

    update: Currently my hsn stripped out of my carb somehow so I have a new carb on the way, as well as a new header :o


    and I'm still going through body clips like crazy!!!
  19. Replies
    7
    Views
    490

    Locked rear differential

    Are there any out yet? I like to do some climbing, and I'm really sick of spinning. I don't want a lsd, I want something solid with no power loss like a lsd.
  20. Replies
    28
    Views
    1,582

    I made something for the same problem, but...

    I made something for the same problem, but completely different. I took those little clips that come with car speakers... basically a piece of metal 1/4" wide, and 1" long, in a U shape, with a hole...
  21. So I took my revo to a Motocross track today

    Wow.... just wow. All the jumps at the little RC tracks around here are kinda sucky, no landing and poor launch. The one jump at the MX track the truck flew off to as high as my neck, that's a good...
  22. Replies
    2
    Views
    899

    Actually I fixed the problem already. I believe...

    Actually I fixed the problem already. I believe that the electric motor was stuck in a deadspot. I dissasembled the whole ez start trying to trace the problem. When I took the motor out I touched...
  23. Replies
    9
    Views
    335

    I'm no expert at all on electric... well on...

    I'm no expert at all on electric... well on anything really. But from what I understand of how electric motors work, they create magnetic fields which pull the shaft around causing it to spin......
  24. Replies
    9
    Views
    335

    Alright guys, problem solved!!! It seems...

    Alright guys, problem solved!!!


    It seems that the electric ez start motor was just at a deadspot, and so it wasn't able to get itself started spinning. I find it strange that when turning the...
  25. Replies
    9
    Views
    335

    All wires look to be in perfect condition. There...

    All wires look to be in perfect condition. There is compression when turning it by hand yes :)

    When ez start is not plugged in, the motor light turns on yes. When it is plugged in, both the...
Results 1 to 25 of 35
Page 1 of 2 1 2