Search:

Type: Posts; User: ip42800ht

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    7
    Views
    137

    Replacing the starter shaft with the OWB is...

    Replacing the starter shaft with the OWB is recommended....
  2. Replies
    12
    Views
    160

    One of the worst features of the original...

    One of the worst features of the original reversing transmission. FOC will eliminate the bucking.
  3. Replies
    7
    Views
    203

    Normal. If it runs fine, leave it alone. Nitro...

    Normal. If it runs fine, leave it alone. Nitro engines will require tuning on a daily (or even hourly) basis.
  4. Replies
    12
    Views
    351

    Tamiya #42260, pricey, but a nice reamer.

    Tamiya #42260, pricey, but a nice reamer.
  5. Replies
    13
    Views
    527

    Sounds like LSN might need to be leaned out. Try...

    Sounds like LSN might need to be leaned out. Try it 1/16 turn at a time.
  6. Replies
    2
    Views
    130

    You may have a broken clutch spring. Pull the...

    You may have a broken clutch spring. Pull the engine and inspect the clutch assembly.
  7. Replies
    13
    Views
    527

    Have you tried raising the idle stop screw or...

    Have you tried raising the idle stop screw or leaning out the LSN yet? Remove air filter and visually make sure operation of the brakes does not close the carburetor further. It is possible the...
  8. Replies
    43
    Views
    1,361

    The pull start screws require minimal torque or...

    The pull start screws require minimal torque or else the system will bind. Blue loctite is reccomended.
  9. Replies
    10
    Views
    191

    Depends on ambient temperature, humidity,...

    Depends on ambient temperature, humidity, altitude, air filter / exhaust setup, nitro %....

    HSN needs to be richened.
  10. Thread: Faster!!

    by ip42800ht
    Replies
    9
    Views
    271

    You could try: -Forward only conversion...

    You could try:
    -Forward only conversion
    -Lighter wheels/tires (assuming stock chevrons)
    -Resonator exhaust
    -Gearing change

    The easy route would be a 3.3. Even with all those upgrades above,...
  11. Replies
    8
    Views
    123

    Idle may be set too low, LSN may be too rich, or...

    Idle may be set too low, LSN may be too rich, or your linkage/trim may be incorrectly set, allowing the carburetor to close further when applying the brakes vs. at its neutral postion.

    For cold...
  12. Replies
    3
    Views
    155

    Make sure the linkage is set correctly. At...

    Make sure the linkage is set correctly. At neutral throttle the carburetor opening should be at it's minimum opening. Sometimes with an incorrectly set trim and/or linkage the carburetor opening can...
  13. Replies
    2
    Views
    225

    Proper gear mesh, slipper adjustment, and going...

    Proper gear mesh, slipper adjustment, and going for smooth landings will go a long way in keeping the spur intact. If the spur doesn't go, something else more expensive and time consuming to replace...
  14. Replies
    14
    Views
    639

    One of my favorite small block engines. Easy to...

    One of my favorite small block engines. Easy to tune, solid power, good fuel economy, and you can get quite some fuel through them before needing a rebuild.
  15. Replies
    11
    Views
    433

    The Pro .15 used to run around 300. It's...

    The Pro .15 used to run around 300.

    It's important to remember ambient temperature plays a big role in engine temperature, and that you generally shouldn't tune for temperature.
  16. Replies
    14
    Views
    639

    http://s18.postimg.org/x4p2g0hux/PDR_0215.jpg...

    http://s18.postimg.org/x4p2g0hux/PDR_0215.jpg
    http://s18.postimg.org/tjt6wsdbd/PDR_0213.jpg
  17. Replies
    23
    Views
    887

    94 BMW 540i Let's just say 282 ponies out of a...

    94 BMW 540i

    Let's just say 282 ponies out of a 4.0L 32V V8 is plenty for a 15 year old.
  18. Replies
    19
    Views
    422

    I've yet to meet a young boy who sees nitro R/C...

    I've yet to meet a young boy who sees nitro R/C vehicles in action and doesn't immediately want one.
  19. Replies
    14
    Views
    788

    Way too tight. Back it off.

    Way too tight. Back it off.
  20. Thread: Fuel

    by ip42800ht
    Replies
    10
    Views
    540

    30-33% nitro is the bees knees. Great power jump...

    30-33% nitro is the bees knees. Great power jump from 20% and the engine can be run cooler and richer, while still providing more power over an engine on 20% that is running leaner. I used 20 in the...
  21. Replies
    17
    Views
    533

    T-Maxx Pro .15, T-Maxx 2.5, Revo 2.5, Revo 3.3,...

    T-Maxx Pro .15, T-Maxx 2.5, Revo 2.5, Revo 3.3, 4-Tec 2.5, Jato 2.5, E-Revo, Slash 4x4
  22. Replies
    7
    Views
    237

    You won't have an issue. Follow proper break-in...

    You won't have an issue. Follow proper break-in techniques.
  23. I wouldn't buy used unless you have experience in...

    I wouldn't buy used unless you have experience in surface vehicles. It's the safer play if you don't know what you're doing. Hard to beat a factory fresh Traxxas ride.
  24. Replies
    3
    Views
    334

    Great fuel. Always re-tune for new blends.

    Great fuel. Always re-tune for new blends.
  25. Make sure it's not running too lean. Spin the...

    Make sure it's not running too lean. Spin the clutch bell to see if anything is seized or worn.

    These engines will lean out as they reach operating temperature. They also need constant tuning due...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4