Search:

Type: Posts; User: jimbo74

Page 1 of 20 1 2 3 4

Search: Search took 0.60 seconds.

  1. Replies
    2
    Views
    56

    You can't run 2.2s unless you run a low backspace...

    You can't run 2.2s unless you run a low backspace version up front. Most 2.2s wont clear the 4wd knuckles
  2. there is a different offset front to rear..... so...

    there is a different offset front to rear..... so rear buggy wheels all around wont be even
  3. Replies
    10
    Views
    192

    Hey, I used 8-32 threaded rod from the hardware...

    Hey, I used 8-32 threaded rod from the hardware store and 4mm long rpm ends... has worked like a charm....
  4. Replies
    22
    Views
    337

    It is going to smack, that what it was designed...

    It is going to smack, that what it was designed to do.... you can't really expect it to not hit when jumping it, not with being its size
  5. Thread: lipo storage?

    by jimbo74
    Replies
    3
    Views
    106

    Just charge it to storage after using it. It...

    Just charge it to storage after using it. It takes a lot longer for the charger to burn off voltage than charge it in.... just to note, leaving it fully charged, may cause it to puff..... ask me how...
  6. They will bolt on, but the slash uses different...

    They will bolt on, but the slash uses different offsets front and rear. One end will be wider than the other
  7. Thread: motor help

    by jimbo74
    Replies
    3
    Views
    49

    What motor? If you are talking about a brushed...

    What motor?

    If you are talking about a brushed motor, many people prefer the water method


    Brushless motors don't need to be broken in
  8. Replies
    3
    Views
    80

    Depends on other factors. I suggest you do some...

    Depends on other factors. I suggest you do some reading about batteries to get familiar.

    You could have a million mah, but if it has a 1c discharge rate, it wont work.......
  9. Thread: rc body

    by jimbo74
    Replies
    2
    Views
    69

    Well if you are going unique it probably isn't...

    Well if you are going unique it probably isn't made directly for the slash.....

    The slash is a bit of an odd size. Proline does make an 81 bronco for the slash
  10. Thread: 100 MPH setup?

    by jimbo74
    Replies
    4
    Views
    113

    While it is possible, it isn't likely..... 60 mph...

    While it is possible, it isn't likely..... 60 mph s already quite a bit.....
  11. Replies
    10
    Views
    192

    Same width as the rear arms, front arms are...

    Same width as the rear arms, front arms are significantly shorter
  12. Replies
    15
    Views
    201

    um..... ...

    um.....

    http://lcdn.dollarhobbyz.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/x/o/xo-1_axle_carriers.jpg
  13. Replies
    28
    Views
    407

    I run hot glue in my diffs ;)

    I run hot glue in my diffs ;)
  14. Thread: Pre-Cut Bodies

    by jimbo74
    Replies
    7
    Views
    123

    I have used kitchen scissors, from harbor...

    I have used kitchen scissors, from harbor freight. Worked just fine. Just took my time, and made small cuts.....

    It doesn't have to be perfect, it is a toy car. If you are nervous, cut less than...
  15. Replies
    28
    Views
    407

    sounds like you need to check your bearings or...

    sounds like you need to check your bearings or anything else for binding......
  16. Replies
    6
    Views
    103

    The 4x4 really needs an 1/8th system in it. In my...

    The 4x4 really needs an 1/8th system in it. In my opinion
  17. Replies
    9
    Views
    152

    Drag race or what? That is a pretty decent combo....

    Drag race or what? That is a pretty decent combo. What about the 2400kv motor from the drag car and the esc? Have you changed the gearing? I am not quite sure what your issue is with upgrading, you...
  18. Replies
    49
    Views
    1,051

    while I think this build looks awesome, and will...

    while I think this build looks awesome, and will probably drive awesome, I read that you want to smoke everyone that talks trash about it being a Slash.... but it really isn't anymore.....

    It is...
  19. yes, but they were never made by traxxas for sale...

    yes, but they were never made by traxxas for sale

    sure, there were the limited edition promoter wheels, but not available as a part to buy....
  20. the monster jam and skully wheels are grey, not...

    the monster jam and skully wheels are grey, not green
  21. Replies
    10
    Views
    144

    then get the screw issue fixed and do the tranny...

    then get the screw issue fixed and do the tranny flip.....

    if you can't afford parts, then put it on the shelf.....
  22. Replies
    9
    Views
    132

    has anyone here ever used a 4wd with the front...

    has anyone here ever used a 4wd with the front drivetrain removed? I have, it was horrible.....
  23. Thread: Feedback

    by jimbo74
    Replies
    3
    Views
    65

    I have always liked my TMaxx, but have heard...

    I have always liked my TMaxx, but have heard negative stories about the EMaxx. THAT said, I have a 2wd and 4wd stampede. Both are pretty solid. I do like the wide mod on the 2wd. Really, wasn't super...
  24. Replies
    4
    Views
    80

    Could be a lot of things. Were you ever able to...

    Could be a lot of things. Were you ever able to do wheelies with it? What electronics do you run?
  25. Replies
    6
    Views
    380

    The difference is you will not be able to run the...

    The difference is you will not be able to run the new motor on the old esc
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4