Search:

Type: Posts; User: chickenman242

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    595

    that savox servo will work great ,if you have a...

    that savox servo will work great ,if you have a tx that can adjust the end points like the traaxas radio you will get the full effect of the steering mods.
  2. Replies
    8
    Views
    730

    picco .26 is discontinued ,as been for nearly a...

    picco .26 is discontinued ,as been for nearly a year,i would look at the picco .21 max or the ofna .28 max both use the ofna mount and are a direct drop in ,the .28 will benefit with a bb exhaust...
  3. Replies
    10
    Views
    473

    there is a dude on another forum who makes the...

    there is a dude on another forum who makes the adaptors ,I have bought a few and they are a good bit of gear search ebay for revo big block adaptor think from memory they are under $20
  4. Replies
    10
    Views
    473

    either a ths big block exhaust with a adaptor or...

    either a ths big block exhaust with a adaptor or check ebay for a trinity clone ,I've run ths on several rig with good results and have the clone exhaust fitted to another and it works good.
  5. Replies
    15
    Views
    1,400

    you could put some springs between the brake pads...

    you could put some springs between the brake pads similar to whats done on the t maxx brakes
  6. Replies
    3
    Views
    917

    go on ebay and get a mount from a 3.3 4tec ,chop...

    go on ebay and get a mount from a 3.3 4tec ,chop shops have them very cheap such as jennys rc or dollarhobbies .
    while you are there you can get the linkages and exhaust .
  7. Replies
    62
    Views
    2,877

    got to jennys rc on ebay and look for a savage...

    got to jennys rc on ebay and look for a savage clutch kit usually comes with a 17t bell and for a .28 your best to start with 17/36 gearing after that you can adjust for your conditions ,I have just...
  8. its a 4908 which is the extended version , you...

    its a 4908 which is the extended version , you can tell by the gap between the muffler and the radio box plus it has been fitted with reverse and as a micro servo where as the 4909 have a full sized...
  9. Replies
    20
    Views
    1,177

    what temp is your engine getting to when its...

    what temp is your engine getting to when its running ,I did read that you said around 200f ,if that's after a few runs its too rich ,to me you need to lean it out a bit that would be causing it to...
  10. Replies
    10
    Views
    712

    How much has this setup cost roughly I likes the...

    How much has this setup cost roughly I likes the look of your setup and I'm wanting to rehash my be maxx
  11. Replies
    3
    Views
    123

    to tell you the truth I never really noticed but...

    to tell you the truth I never really noticed but I think bump in is supposed to give you more grip while conering where as bump out will be better suited for larger tracks with less turns.
    I have...
  12. Replies
    3
    Views
    123

    out of the box 4909 has both front and rear in...

    out of the box 4909 has both front and rear in the middle ,when I set mine up to race I redid mine so the font and rear are both at the top . from memory upper in bump in and lower is bump out.
  13. For hinge pins , Lunsford make a great set that...

    For hinge pins , Lunsford make a great set that can be used with rpm arms and for the knuckles/uprights you can use the ones that come standard on the erevo which have a bigger bearing and a metal...
  14. Replies
    50
    Views
    2,096

    http://i1284.photobucket.com/albums/a569/bigbozza2...

    http://i1284.photobucket.com/albums/a569/bigbozza242/output_zpszgelzl0v.jpg that's where I'm at atm I need to wait for a new carb arm as I broke this one trying to get the throttle to open and close...
  15. Replies
    50
    Views
    2,096

    everything is fairly straight forward but the...

    everything is fairly straight forward but the linkage needs a lot of tweaking in fact I broke the carb arm tightening and loosening it ,I'm going to redo the linkage again ill post some pics up when...
  16. Replies
    50
    Views
    2,096

    I hope your mount comes with instructions, the...

    I hope your mount comes with instructions, the one I just bought didn't ,most of the stuff is fairly self explanatory but I still cant figure out where the spring goes lol.
  17. Replies
    21
    Views
    877

    I have the ofna .28 in a 2.5 revo and its one of...

    I have the ofna .28 in a 2.5 revo and its one of my favourites ,for the clutch I used an m2c one and its been great also had no problems with the strc clutch setup also
  18. back in the day before I knew about the ofna tank...

    back in the day before I knew about the ofna tank for the maxx I used a small header tank from an rc plane or maybe a heli ,it would have ben like 20-25cc I think it would a bit of trial and error.i...
  19. the problem maybe the fact the sport only has a...

    the problem maybe the fact the sport only has a 75cc tank and a 523 will draw a bit of fuel and have been know for left turn lean issues you may have to run some sort of small header tank to keep...
  20. check if there is an airleak in your fuel tank or...

    check if there is an airleak in your fuel tank or lines ,if you get bubbles in your lines while idleing theres a chance it could be leaning out and causing it to wot
  21. Replies
    11
    Views
    1,263

    the pro comes with a brace like the revo ,if you...

    the pro comes with a brace like the revo ,if you want to go hardcore use the m2c chassis brace it does however require some drilling of the chassis
  22. Replies
    34
    Views
    2,399

    the build im doing is for my cousin so I don't...

    the build im doing is for my cousin so I don't want his to be too much faster than mine , I really want to line my ofna .28 max against his lrp just to see what the difference is ,if I get chopped I...
  23. Replies
    34
    Views
    2,399

    so what happened to the .28 max?? I thought I saw...

    so what happened to the .28 max?? I thought I saw your tuck around on here or another forum... cant hurt to have more power ,I'm currently gathering parts to do a z.28 into a 3.3 I jagged a new era...
  24. Replies
    5
    Views
    200

    check to see where your blue bump stops are on...

    check to see where your blue bump stops are on the slayer they are inside the shock to limit the shocks travel
  25. Replies
    4
    Views
    95

    there are 3 pins in the tranny , one on the...

    there are 3 pins in the tranny , one on the primary input shaft another that holds the 2nd gear clutch on and the other hold the primary output gear on .
Results 1 to 25 of 180
Page 1 of 8 1 2 3 4