Search:

Type: Posts; User: CumminsDriver

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    0
    Views
    125

    Selluminis great seller!

    Bought a transmission from Selluminis. Fast shipping and good communication. Highly reccomended:cool:
  2. Replies
    8
    Views
    215

    You need to find the idle speed screw on the...

    You need to find the idle speed screw on the carburetor, and turn it clockwise. Probably the easiest way for you to do it is to start the engine and get it up to temperature. Then with it sitting...
  3. $80 shipped

    $80 shipped
  4. Feel free to make offers!

    Feel free to make offers!
  5. E-Maxx Chassis and Transmission For Sale

    Hey guys. I bought an E-Maxx a little bit back and ended up pulling the front/rear ends to use for a different project. I dont need the chassis/transmission so I am putting it up for sale. I drove...
  6. Replies
    7
    Views
    803

    ajcar - Thanks for the compliment. Just thought I...

    ajcar - Thanks for the compliment. Just thought I would try it out. I havent really been able to drive it yet, but im thinking it should perform pretty well.

    PowerDemon - Im pretty sure Ill be...
  7. Replies
    7
    Views
    803

    Ok, I have some pictures now. haha So, I...

    Ok, I have some pictures now. haha

    So, I ordered 4 HPI Trophy Buggy Rear Shocks(same as truggy front and rear). After I ordered the shocks I found out that the suspension wont compress fully...
  8. You can if you are only running rear wheel drive...

    You can if you are only running rear wheel drive - No front diff at all

    If you are wanting the rear end to spin both tires pretty well, I would put some 500k diff oil in it. I think that will get...
  9. Replies
    7
    Views
    803

    PowerToTheMaxx- I wouldnt mind a setup like that...

    PowerToTheMaxx- I wouldnt mind a setup like that honestly, but Im trying to not spend a lot on a power system really. Im thinking the 775 (or dewalt) is probably kind of pointless since I have a good...
  10. Replies
    7
    Views
    803

    Here we go - E-Maxx 3905 Project

    Hey guys. I haven't been around for a little while. Kind of slowed up in the hobby but now that winter is coming around I cant resist a project that I can piddle with in the house while its cold...
  11. Replies
    116
    Views
    25,291

    That telluride looks awesome. Im seriously...

    That telluride looks awesome. Im seriously considering one next time i decide to buy an rc. Possibly after I sell a couple that i already have. It would be nice if traxxas had incorporated some...
  12. Replies
    12
    Views
    586

    The single VXL would have more power than the...

    The single VXL would have more power than the stock setup by a fair amount from what I have seen.
  13. Replies
    12
    Views
    586

    Personally I would stick with 3s if going...

    Personally I would stick with 3s if going brushless. I have found even in my bigger brushless MT's that 4s with a powerful brushless system can be a little too much at time. A VXL would probably be...
  14. Replies
    8
    Views
    949

    I personally really like the 2.2 Yokohama...

    I personally really like the 2.2 Yokohama Geolander. They have good traction, but they are also hard enough that they wear really well, and the fact that they arent really soft also keeps them from...
  15. Replies
    3
    Views
    305

    No offense but I'm not wanting anyone's opinion...

    No offense but I'm not wanting anyone's opinion on Integy, I just want to know if I can buy a rebuild kit since I haven't found it online yet.
  16. Replies
    3
    Views
    305

    Integy CVD's

    Hey guys. I just bought a used 3.3 Jato and it has Integy CVD's on it. However, one of them needs a rebuild kit because the insert that houses the grub screw and drive pin is gone. Does anyone know...
  17. Does it start right back up after it dies? It...

    Does it start right back up after it dies? It could be low on pinch.. It sounds like you are starving it for fuel on the top end though. Turn the high speed needle 1 whole turn out and see if it runs...
  18. Wanted - Jato header and aluminum pipe

    Hey guys, I have a little bit of a project going on and I am in need of a 3.3 Jato header and pipe. The aluminum pipe, not the plastic one. Just send me a PM with a price shipped to 40422 if you have...
  19. Replies
    637
    Views
    44,906

    What about "100 proof" ? Thats what i'd name it.

    What about "100 proof" ? Thats what i'd name it.
  20. Replies
    26
    Views
    1,210

    You can run lipos with any ESC, you just need a...

    You can run lipos with any ESC, you just need a low voltage alarm if the ESC does not have a lipo cutoff.
  21. Replies
    34
    Views
    1,763

    This is one of my old 3906's (I have had 5 of...

    This is one of my old 3906's (I have had 5 of them. lol) with stock motors, stock gearing, and lipo's:


    http://www.youtube.com/watch?v=KDahbJ72nrU

    You can see there is no shortage of...
  22. Replies
    34
    Views
    1,763

    You shouldnt have a reverse rotation. It may not...

    You shouldnt have a reverse rotation. It may not hurt a lot, but it wont help. The timing is setup differently.

    I just bought a 3906. Its in pretty decent shape with exception of a few parts and...
  23. Replies
    4
    Views
    1,507

    No problem, I realized that after you tried to...

    No problem, I realized that after you tried to write me. Its clear now. Ill send you my paypal. Thanks

    Eric
  24. Replies
    4
    Views
    1,507

    To the top :cool:

    To the top :cool:
  25. Replies
    4
    Views
    1,507

    Bump.......

    Bump.......
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4