Search:

Type: Posts; User: zach23

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1,515
    Views
    80,511

    Any opinion on those wheels? Are they OK?

    Any opinion on those wheels? Are they OK?
  2. Thread: 1/16 Mini Emaxx

    by zach23
    Replies
    234
    Views
    24,504

    I am totally impressed with your work!

    I am totally impressed with your work!
  3. Replies
    4
    Views
    188

    I'm here too! Just more focused on my Axial SCX10...

    I'm here too! Just more focused on my Axial SCX10 :cool:
  4. Replies
    18
    Views
    852

    Good idea and nice fabrication. And gearing is...

    Good idea and nice fabrication. And gearing is still possible to change if I'm not mistaken ;)
  5. Thread: Squishy rearend

    by zach23
    Replies
    6
    Views
    465

    go for stiffer springs - from the summit range. I...

    go for stiffer springs - from the summit range. I am using below setup and love it!

    FRONT:
    7245: Spring, shock (GTR) (2.925 rate, blue) (1/16 Summit)

    BACK:
    7246: Spring, shock (GTR) (3.2...
  6. Replies
    4
    Views
    292

    You could refresh nimh batteries per few weeks on...

    You could refresh nimh batteries per few weeks on a charger with discharge/charge cycle - if your charges has such option.
    Slow charge would be better - at C/10 or below (10% of the rated capacity)
  7. Replies
    4
    Views
    304

    +1 on bad servo

    +1 on bad servo
  8. Replies
    9
    Views
    419

    you might be in training mode - check the manual...

    you might be in training mode - check the manual and set normal mode on ESC.
  9. Replies
    4
    Views
    355

    this way it cannot work - 6v is enough just for...

    this way it cannot work - 6v is enough just for 2-3 LEDs in series depending on colour (power consumption).
    you need to use separate circuits and resisors for 8 LEDs

    This could help you:...
  10. Replies
    8
    Views
    638

    I am also running 2x2S to get better punch and...

    I am also running 2x2S to get better punch and longer run times. Moreover I like extra stability because of higher weight.
    Suspension have to be fine tuned - I have summit blue springs in front and...
  11. Servo is very likely to cause overall behaviour...

    Servo is very likely to cause overall behaviour problems. No mods required, just servo reversing on the remote.
  12. Replies
    1
    Views
    331

    Check where this noise is coming from. I would...

    Check where this noise is coming from. I would guess:
    - the diffs - new ones usualy have "tight spots" on the ring, which wear out over time - would match half wheel turns
    - other then that oil...
  13. Thread: Water testing

    by zach23
    Replies
    12
    Views
    489

    true, true ... didn't notice ...

    true, true ... didn't notice ...
  14. Thread: Water testing

    by zach23
    Replies
    12
    Views
    489

    Put your ESC and receiver (just in case ...) in...

    Put your ESC and receiver (just in case ...) in dry rise - it should take all the moisture out of your electronics over a night or two.
    Could be saved since it is still partially operational.
  15. Replies
    6
    Views
    307

    Maybe only the screw holding the pionion gear on...

    Maybe only the screw holding the pionion gear on the motor is loose or even lost?
  16. If you plan to stay in the hobby I suggest you...

    If you plan to stay in the hobby I suggest you invest in a good microprocessor charger with LIPO balancing capability. It lets you monitor amps that went into the battery and charges much faster than...
  17. Thread: LiPo questions

    by zach23
    Replies
    16
    Views
    916

    I also think that 2x 2S in parallel delivers more...

    I also think that 2x 2S in parallel delivers more power to the system, since both batteries are drained and ESC has more amps to feed the motor.
  18. Have you tried both servo channels? Possibly only...

    Have you tried both servo channels? Possibly only broken, badly bend wire???
    Can you double check servo on a different/operating system? How old is your BB?
  19. Thread: LiPo Problems

    by zach23
    Replies
    18
    Views
    615

    What batteries? What charger? Lipos were balanced...

    What batteries? What charger? Lipos were balanced properly and undamaged? There is a lot of questions to investigate what has happened. I hope your electronics is OK!
  20. Replies
    2
    Views
    276

    OK - it is hex 1,3mm

    OK - it is hex 1,3mm
  21. Replies
    2
    Views
    276

    I've found it is 0,50". Should be 1,2mm hex. Will...

    I've found it is 0,50". Should be 1,2mm hex. Will confirm when I check which bit fits.
  22. And my guess would be worn gears inside the servo...

    And my guess would be worn gears inside the servo itself. The final gear that you attach servo horn on the "inside" is connected to the potentiometer that tells the servo position of the horn. To me...
  23. http://img683.imageshack.us/img683/4686/43641234.j...

    http://img683.imageshack.us/img683/4686/43641234.jpg
  24. Thread: Mudding!!!!

    by zach23
    Replies
    35
    Views
    1,250

    If in doubt keep exploaded prints at hand and...

    If in doubt keep exploaded prints at hand and most of maintance jobs you can easly find on Youtube for guidance.
  25. Chassis braces from thetoyz add a lot to overall...

    Chassis braces from thetoyz add a lot to overall stiffness of the truck. While placing an order you could also look for Aluminum Steering Arm Post...
Results 1 to 25 of 182
Page 1 of 8 1 2 3 4