Search:

Type: Posts; User: Kitteh298

Page 1 of 20 1 2 3 4

Search: Search took 0.48 seconds.

  1. Replies
    35
    Views
    1,873

    Yes, the axle is replaced and the 17mm hub slides...

    Yes, the axle is replaced and the 17mm hub slides right over that.
  2. Replies
    27
    Views
    519

    I use the heat gun method, seems to be the...

    I use the heat gun method, seems to be the quickest and easiest way to get a tire off.

    Don't have to deal with chemicals or dirty your kitchen/house.
  3. Replies
    6
    Views
    221

    I wrapped mine up with heat shrink outside the...

    I wrapped mine up with heat shrink outside the receiver box
  4. Replies
    21
    Views
    638

    I rinse with hot water and blow off with air...

    I rinse with hot water and blow off with air compressor, but beforehand, you'll want all bearings greased and screw heads oiled.

    Hot water tends to steam off easy especially if most is removed.
    ...
  5. Replies
    13
    Views
    323

    TRA6753 should be all you need to fix your issue.

    TRA6753 should be all you need to fix your issue.
  6. Thread: minnesota

    by Kitteh298
    Replies
    8
    Views
    283

    South about an hour

    South about an hour
  7. Thread: minnesota

    by Kitteh298
    Replies
    8
    Views
    283

    I live here, so I suppose so xD

    I live here, so I suppose so xD
  8. Replies
    12
    Views
    456

    I'd say tekno, I use them on my 4s mamba monster...

    I'd say tekno, I use them on my 4s mamba monster slash 4x4 work well, only had a few breakages when I was absolutely wailing on it.
  9. Replies
    46
    Views
    1,153

    I've run the smaller slipper for quite a while,...

    I've run the smaller slipper for quite a while, finally decided to opt for a rather needed upgrade.(after finding a broken slipper pad) The Revo slipper with aluminum pads as noted by Billy-bones....
  10. Replies
    13
    Views
    432

    The only real fix is 17mm hexes, unless you're...

    The only real fix is 17mm hexes, unless you're running brushed, 12mm really doesn't have a place on a heavy high power truck. I've been down this road with my 2.8 trenchers on my truck. Super gluing...
  11. I second that, the Hot Racing cage is where its...

    I second that, the Hot Racing cage is where its at. Unfortunately with lots of head on collisions the hoop over the truck bends front and back and eventually broke. I had a brace welded on. Back in...
  12. Replies
    2
    Views
    125

    I have an IKEA table, very solid, durable,...

    I have an IKEA table, very solid, durable, reasonably priced, unlimited leg and top options.
  13. Replies
    13
    Views
    370

    I use a small spring in the cup of my big bone,...

    I use a small spring in the cup of my big bone, its pretty well silent, I like it.
  14. Sounds like you need some more preload going on...

    Sounds like you need some more preload going on if you're bottoming out.
  15. Replies
    18
    Views
    495

    I remove the seals and spray brake clean sort of...

    I remove the seals and spray brake clean sort of at an angle so the bearing spins and knocks dirt and such free, do that on both sides until all grease and dirt is out, then throw some wheel bearing...
  16. Replies
    27
    Views
    766

    The only thing I see wrong with the grease is...

    The only thing I see wrong with the grease is that it looks like most of it is filled with dirt. There's barely any grease in there. I take the bottom plate off mine and pack it full, keeps it quiet...
  17. I've unglued that loctite super glue with a heat...

    I've unglued that loctite super glue with a heat gun very easily a few times already. It's strong and easy to remove.
  18. Replies
    5
    Views
    258

    I went overkill and use a ceramic bearing from...

    I went overkill and use a ceramic bearing from boca bearings. They get much cheaper when you buy the 4 or 10 packs.
  19. Replies
    4
    Views
    265

    Rear hub carriers? Run the offending bolt in...

    Rear hub carriers? Run the offending bolt in backwards and problem solved.
  20. Replies
    2
    Views
    285

    I've been through numerous velineon systems and...

    I've been through numerous velineon systems and can not recommend them. Go with a different system instead. Something from castle would be my recommendation. The funnycar motor and a waterproof esc...
  21. Replies
    4
    Views
    229

    Take the front end off of the truck, (4 screws),...

    Take the front end off of the truck, (4 screws), tug on the front end lightly, remove the screw from the servo linkage into the servo horn, lastly, remove the wheels.

    Now you can move the servo...
  22. This mod is spectacular. My arms moved around...

    This mod is spectacular. My arms moved around like a loose tooth, this tightened them right out without a whole lot of effort. I've been looking for something like this for a while. The loose wheels...
  23. Replies
    4
    Views
    257

    I guarantee you between all of the paint...

    I guarantee you between all of the paint manufacturers you can get something that looks very similar, like a sunrise, burnt, or metallic orange would probably be about right.

    I don't find it is...
  24. Replies
    6
    Views
    141

    You'd probably have to buy steel rod and cut it...

    You'd probably have to buy steel rod and cut it to length if you want spares, those pins really should never wear out.
  25. No, that's not logical.

    No, that's not logical.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4