Search:

Type: Posts; User: rrho170

Search: Search took 0.01 seconds.

  1. Replies
    24
    Views
    675

    They don't want to get dinged for talking about...

    They don't want to get dinged for talking about non traxxas parts.
  2. Thread: Clutch Shoes

    by rrho170
    Replies
    15
    Views
    450

    Poking out there by the pin is ok. Thar part of...

    Poking out there by the pin is ok. Thar part of the clutch does not contact the bell. I also put tiny washers on the pins before putting the shoes on as my last set wore uneven and was pushing bell...
  3. Replies
    2
    Views
    366

    Tqi receiver in large scale use.

    Will a trx receiver hadle the large dual servo setups used in 1/5 buggies and trucks? I know there is a 2nd ch 1 out for that, but is there any current limitations to watch for? Never done large...
  4. Replies
    0
    Views
    542

    Rpm alert on round gauge disabled.

    Am I missing something? Alert disabled in gauge cluster but is enabled in gridb dashboard. How do I enable it in gauge cluster?

    Thanks1
  5. Thread: brake issue

    by rrho170
    Replies
    2
    Views
    152

    Yes. The rod from the servo to the brake lever....

    Yes. The rod from the servo to the brake lever. Make sure the little piece of rubber hose is lust almost touching the lever when at idle. Turn on transmitter and receiver. Work the throttleand allow...
  6. Watch for excessive clutch wear if your idle is...

    Watch for excessive clutch wear if your idle is high. You will see black deposites arounf chassis under spur gear.
  7. Replies
    8
    Views
    351

    Whats is considered normal maintenance interval...

    Whats is considered normal maintenance interval for the clutch? I am barely past half gallon total and the stock is worn to the springs. Now I bet my high idle during break in played a big role in...
  8. Replies
    8
    Views
    351

    The aluminum question was more for the...

    The aluminum question was more for the Centrifugal clutch on the motor.

    Snook, I did have the spring washer in correctly, the fisrt one that fell off was the factory installed one. I believe that...
  9. Replies
    10
    Views
    298

    I have had the one way bearing on thr rear of the...

    I have had the one way bearing on thr rear of the motor twist in the plastic gear and jamb up against the gear housing so tight I had to use tols to pull it out. Pull the EZ start gear set off the...
  10. Thread: Runaway T-Maxx

    by rrho170
    Replies
    20
    Views
    1,844

    There is supposed to be a last known neutral...

    There is supposed to be a last known neutral throttle position that the rx tx leans, though I am not sure how it learns yet.

    You can get a battery watch and mount it on the back window ir get the...
  11. Replies
    8
    Views
    351

    Bell gear clutch wear 3.3.

    On Tank 7 since new in box. Replacing slipper clutch for second time due to nut backing out, this time using locktite.

    Noticed centrifugal clutch is already worn down to springs, likely because...
  12. Check the clutch on the motor. Pop off the e clip...

    Check the clutch on the motor. Pop off the e clip and slide off gear. MAke sure springs are not grinding into bell gear.

    The slipper should be set to where its difficult to turn by hand when the...
  13. FYI the engine ran great at 1/4 throttle for the...

    FYI the engine ran great at 1/4 throttle for the 1st tank. No stalling or high temps or wierd issues.

    UPDATE: Traxxas tech said the engine was normal to have that much resistance without plug in.
  14. New 3.3 and have issues EZ Start and motor.

    Out of the box EZ start would only turn engine over 6 or 7 revolutions and stop out of the box after charging battery 6 hours until light went green. Fuel never reached engine. Not hydro locked
    ...
Results 1 to 14 of 14