Search:

Type: Posts; User: Gadgeteer

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Would you like to see Traxxas race the Slash 4x4 more often?

    lately, Traxxas seems to be more focused on racing Nascar,TORC, and other forms of racing. I think this is great for Traxxas, they are able to bring their brand and our hobby to a wider audience.
    ...
  2. Replies
    11
    Views
    1,655

    The stock e-revo chassis is the best option...

    The stock e-revo chassis is the best option IMO....I have had mine for almost 2 years now.

    Compared to the nitro revo chassis, the erevo chassis has a lower cg since the batteries are positioned...
  3. Replies
    9
    Views
    609

    I have both and I think their both great. ...

    I have both and I think their both great.

    Depends on what you intend to do really.

    IMO the E-revo is a lot more fun, you can jump it higher and much easier to control in the air and land...
  4. Replies
    15
    Views
    853

    Ceramic bearings wont last any longer. Ceramic...

    Ceramic bearings wont last any longer. Ceramic bearings spin a lot better because of their tighter tolerances, but tighter tolerances also mean its more sensitive to dirt.

    The only way to make the...
  5. Replies
    5
    Views
    461

    I just normally use a strong detergent/cleanser...

    I just normally use a strong detergent/cleanser with an old toothbrush......seems to work :)
  6. Get new tires :) Just tried the new cityblock...

    Get new tires :)

    Just tried the new cityblock sc, they are awesome :)
  7. Replies
    27
    Views
    2,097

    Thanks! Can t wait to try it :)

    Thanks!

    Can t wait to try it :)
  8. Replies
    27
    Views
    2,097

    Did Traxxas release a new driveshaft cover? ...

    Did Traxxas release a new driveshaft cover?

    Anyone got info on this?

    Thanks!
  9. Replies
    544
    Views
    322,255

    Sticky: The car tends to oversteer especially with race...

    The car tends to oversteer especially with race tires.

    If you have the rtr version, move the steering link on the steering knuckles to the furthest hole, this will reduce steering.

    You can also...
  10. Replies
    18
    Views
    2,390

    I've read it either here or another forum,...

    I've read it either here or another forum, sometimes symptoms like this could also be because the rotor on the motor is no longer attached to the shaft, therefor the rotor just spins on the motor...
  11. Replies
    14
    Views
    896

    I experienced something similar once, after...

    I experienced something similar once, after looking real close, I noticed there was a very, very small piece of rock stuck in the spur causing the weird noise.

    I just removed it and the truck ran...
  12. Replies
    11
    Views
    534

    If you call traxxas they may send you replacement...

    If you call traxxas they may send you replacement bearings.

    I had issues with the stock motor bearings, i suddenly felt the drivetrain had some binding and traced it down to the motor.

    I...
  13. Replies
    7
    Views
    8,566

    here ya go :) ...

    here ya go :)

    http://www.rcrcr.com/index.php?optio...eral&Itemid=46
  14. Replies
    8
    Views
    1,496

    The rpm arms are great for bashing, but constant...

    The rpm arms are great for bashing, but constant use and impacts will cause the soft flexible arms to bend.

    They are tough and will most likely never break, but when they bend its not best for...
  15. Replies
    16
    Views
    2,128

    If you just bash i would stick with the stock...

    If you just bash i would stick with the stock bfg's or the new kumho tires.

    They are scale and make the truck look good imo :)

    If you need more traction on dirt, you can also try the...
  16. Replies
    5
    Views
    1,422

    I looked at the ring and pinion gear part numbers...

    I looked at the ring and pinion gear part numbers for the emaxx brushless and they are the same ones for the e-revo, part #5379x.



    emaxx
    http://www.traxxas.com/PDF-Library/3908_rear.pdf
    erevo...
  17. Replies
    5
    Views
    1,422

    you can back of the screws on the housing just a...

    you can back of the screws on the housing just a little bit and it will run smoother.

    You can also just leave it alone, after a few runs it will wear in and be smooth...
  18. Replies
    14
    Views
    5,147

    Its a nice mod, but cant really see the...

    Its a nice mod, but cant really see the practicality of it, unless you want to drive your car so far from you you cant see it anymore?
  19. Thread: over heating

    by Gadgeteer
    Replies
    7
    Views
    659

    I have seen some people having similar issues and...

    I have seen some people having similar issues and most of us were thinking it was because of a thermal shutdown, it turns out their lipo's were bad.....

    What is the c rating and capacity of your...
  20. Replies
    8
    Views
    488

    You might want to call traxxas for help, the most...

    You might want to call traxxas for help, the most they can do is give you free bearings and replacement for the other damaged parts.

    Like what the others mentioned, search this forum then do what...
  21. Thread: CST to wt

    by Gadgeteer
    Replies
    1
    Views
    2,008

    Here ya go : ...

    Here ya go :

    http://www.rcrcr.com/index.php?option=com_content&view=article&id=56:shock-oil-cps-vs-wt&catid=31:general&Itemid=46
  22. Replies
    19
    Views
    1,919

    I guess we will have to see whether this is true...

    I guess we will have to see whether this is true or not, could be just a typo on their website :)

    If true, we will have too see how they compare with the 72mm long motors like the novak, but at...
  23. Replies
    19
    Views
    1,919

    been waiting for these motors to come out and see...

    been waiting for these motors to come out and see some reviews on it.

    Cant remember where i read it, but according to tekin, the delays were caused by an rc car manufacturer insisting that it fits...
  24. Replies
    7
    Views
    927

    Did you measure the outer diameter on the center...

    Did you measure the outer diameter on the center diff before or after you used it? just asking because it may have been worn out by a bad bearing, otherwise it should be a snug fit on the stock...
  25. Replies
    18
    Views
    1,596

    yep, the slop is is due to the tie bar that holds...

    yep, the slop is is due to the tie bar that holds the left and right bellcrank together, i think this is to prevent the likelihood of binding(beacuse of dirt) if the tolerance was tighter.

    On 8th...
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4