Search:

Type: Posts; User: shorty00735

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    2
    Views
    839

    Here's a link that might help....

    Here's a link that might help.
    http://www.misbehavin-rc.com/paint-shop/paint.asp
  2. Replies
    23
    Views
    1,701

    Looks great! Why did you keep your rear bumper...

    Looks great! Why did you keep your rear bumper on when you installed the wing mount? I just wanted to know because I have seen a few people run it like this. I took my rear bumper off because I...
  3. Also, if it's cold you need to warm it up first...

    Also, if it's cold you need to warm it up first with a heat gun or hair dryer. I'm in Va and I know its colder there in NY.
  4. Replies
    10
    Views
    455

    If you have a good tuned motor, you won't have...

    If you have a good tuned motor, you won't have any problems with a pull start. When a nitro motor is cold, it doesn't matter what starter system you use. Mine will start on 2nd to 3rd pull almost...
  5. Replies
    10
    Views
    455

    I like the pull start a lot better. Don't have...

    I like the pull start a lot better. Don't have to carry around the ez start wand or charge another battery.
  6. Replies
    3
    Views
    229

    What servo are you running and did you check to...

    What servo are you running and did you check to make sure that the pivot ball screws are not too tight?
  7. Replies
    11
    Views
    357

    Try recentering your servos. Here's a link that...

    Try recentering your servos. Here's a link that explains it: http://www.misbehavin-rc.com/pit-lane/center-servo/g-center-servo.asp
  8. Thread: Slipper?

    by shorty00735
    Replies
    13
    Views
    299

    Thanks Oomp! Do you know if they make the part...

    Thanks Oomp! Do you know if they make the part that holds the pads?
  9. Replies
    14
    Views
    399

    It's not supposed to fully close, but there...

    It's not supposed to fully close, but there should be a small gap when it's in the close position.
  10. Replies
    4
    Views
    237

    You might have to turn your carb, it might be...

    You might have to turn your carb, it might be binding.
  11. Replies
    10
    Views
    316

    Are you going to build it from the ground up?

    Are you going to build it from the ground up?
  12. Replies
    18
    Views
    364

    Thanks, I didn't know you could do this. That's...

    Thanks, I didn't know you could do this. That's why this forum is awesome.
  13. Replies
    10
    Views
    316

    How much money are you willing to spend?

    How much money are you willing to spend?
  14. Replies
    5
    Views
    271

    joey79: Just loosen the slipper a bit.

    joey79: Just loosen the slipper a bit.
  15. Replies
    4
    Views
    237

    Sounds like you have a loose slipper. The carb...

    Sounds like you have a loose slipper. The carb isn't supposed to close all the way. There should be a little gap when it is closed. If it is open it will act like it's idling really high.
  16. Replies
    6
    Views
    334

    Yes, the FOC will fix it. It will eliminate the...

    Yes, the FOC will fix it. It will eliminate the reverse gear the one that broke and the opti-drive. You can't just take out the reverse gear and put it back together.
  17. Replies
    13
    Views
    337

    Check your slipper or your drive shafts.

    Check your slipper or your drive shafts.
  18. Sounds like something is melting. Do you have...

    Sounds like something is melting. Do you have any pics?
  19. It happens. I did it when I first got my Rustler.

    It happens. I did it when I first got my Rustler.
  20. Replies
    9
    Views
    228

    Yes, I had problems during and after break in. ...

    Yes, I had problems during and after break in. Once I figured the factory settings were too rich, it opened up.
  21. Replies
    8
    Views
    371

    Thanks, I didn't know about this.

    Thanks, I didn't know about this.
  22. Replies
    9
    Views
    228

    In my case, it was the LSN. Mine is really...

    In my case, it was the LSN. Mine is really touchy. I just make small adjustments with it.
  23. Replies
    9
    Views
    228

    Try the HSN at 5-6 turns out.

    Try the HSN at 5-6 turns out.
  24. Replies
    9
    Views
    228

    Try the LSN at 5.5 turns out.

    Try the LSN at 5.5 turns out.
  25. Replies
    18
    Views
    364

    I see no other way to get to the screws that hold...

    I see no other way to get to the screws that hold the drive shafts to the diffs.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4