Type: Posts; User: HiTechRdNeck
I dug my old T-Maxx out, installed a OS .18 CV-RX and a new shell. Yesterday I picked up the blue T-Maxx with locked differential, MIP CV’s, OS .15 Hyper, FOC. I need to work on the slide carburetor...
Hello, it’s been a year or so since I posted last and about the same amount of time since firing up the T-Maxx.. I see a couple names that I remember, BobR and Ovalqueen.
I decided to get it ready...
Your speakers will actually be better off with the higher powered head unit than a 5 or 10 watt standard unit.
The higher powered units will produce the required power to produce the volume you...
Edit: Sweat should be “Sweet” My spelling sucks.
Yesterday, I couldn’t spell “Engineer”, today I is one!:o
Excellent choice, Have you noticed the wide viewing angle? The one I was looking at, I could go from side to side, got down on the floor to look up at it and it still looked great. Since TV show...
Laser R&D technician
I help design and build prototype marking/etching laser systems.
Hey Joe Reese I wonder if we use any of your optics products, do ya make FF lens’s HR,FR mirrors,...
I totally agree with you. I bought one of the better handy cams for around $1000.00
It started displaying an error code. After calling Sony and with just the error code I was told how...
I watched it Wednesday night.
I did not rent an action flick to see that weird makout scene. And I thought the special effects were a little over done.
The sound was incredible, nothing like...
Here is the link to the Online Manual
The low speed needle is preset so you just have the high speed mixture to deal with.
Here is my experience and modifications with the K&B .18
Yep I see them, the camo body and black wheels look good!
I made a cheep mod that spreads the pressure of the screws out, some time ago. Seems to be working good for me.
Here is the post:
My Servo mounting mod
Just have to figure out how to put a blade on her!:D
RC MOWER Movie
What rkilling1 said is important so look for a CV-RX
If your replacing the TRX15 that had a rotary carb. and don’t want to change your linkage and add parts, go with the engine with the 10E Rotary...
First off I don’t have a 2.5 to compare with anything, (I would like to try one once someone has them in stock) But, I keep reading that the CV-RX engines are weak on the low end. If this is so, I...
Welcome to the boards!
First off, the proper gear mesh is very important. You should slide the Engine towards the Spur gear until the clutch bell gear just seats to the spur gear, but far...
Do you use the Servo grommets or the Nylon washers I am talking about in my post. In your plane and heli?
I was thinking about trying the grommets too, until I read this post and HolmWreckers reply and the reply about not using the brass inserts. Both made sense to me, yet I still wanted some added...
The rubber grommet was Discussed here
After taking my T-maxx out for its spring time run at a soon to be BMX track. I discovered that I had broken all 3 of my servos. My steering servo that was a Cirrus CS80 MG and had a clear case made...
It sounds like your low on Freon (R134a) there is a pressure switch in the suction (low) side that senses if the pressure is too low to protect the compressor. Before you turn on the air conditioner...
My wife and I watch Red Green about every Saturday night on PBS. We went out last week looking for the “Duct Tape Forever” movie to rent or buy, no one in this area seems to know anything about them....
Here are two ways to do it.
Use a LM317T adj. voltage reg. and build this circut.
Or get a LM7805 Fixed +5VDC reg. and add 3 1N4001 diodes in...
Do you have a radio yet? If not do a search for "EchoLink" this will allow you to talk to other amatuers and repeaters VIA a computer with a sound card, mic. and internet...
I don't frequent this board as much as I used to, so you probably haven't seen any of my post.
I'm a Tech+ got my tech. back in 93 and then got my 5WPM code a year or two later.
I use the...