Search:

Type: Posts; User: samk

Page 1 of 7 1 2 3 4

Search: Search took 0.03 seconds.

  1. Was thinking about what you said, all parts...

    Was thinking about what you said, all parts replaced because the original parts simply do not hold up on 3 S. diffs stripped with barely any bashing. Arams break on impact. Servo just died one day....
  2. you have a point but I don't like funny cars :-)

    you have a point but I don't like funny cars :-)
  3. Decided to stick with the revo and get the alum chasis

    I was debating If I should get a 1/10 traxxas or a rally or something else and then I thought about it and since my merv (BB) is here and I had invested money in it I decided maybe better to get the...
  4. Replies
    5
    Views
    290

    Just having a hard time deciding between spending...

    Just having a hard time deciding between spending money on a 1/10 or rebuild my BB merv :-).
  5. Replies
    5
    Views
    290

    anyone have experience with the hot racing...

    anyone have experience with the hot racing chassisi?
  6. Thread: switch to 1/10?

    by samk
    Replies
    13
    Views
    291

    No plans to trade it !:) So maybe redo the...

    No plans to trade it !:)

    So maybe redo the thing again. I found some cool CVD from GPM that are new. well new since I last used the revo 2 years ago :-) They look like original ones but not...
  7. Replies
    9
    Views
    291

    what do you think of this setup?

    I will get a 1/10 revo I think and this is what i think I will setup.

    Is this an excellent setup? what else would you recommend I get ?


    Tekin T8 2000 Motor and ESC for no cogging but is it...
  8. Thread: switch to 1/10?

    by samk
    Replies
    13
    Views
    291

    switch to 1/10?

    I have a revo and not very satisfied with handling :-(. well... I mean using the castle 5700 kv motor and ESC combo :)

    I have oversized tires that I have taped on the inside and then I had to...
  9. Replies
    5
    Views
    833

    So an upgraded driveshaft and diffs would be all...

    So an upgraded driveshaft and diffs would be all that is needed to enjoy 6s?
  10. Replies
    5
    Views
    833

    the NEW e revo brushless truck

    I have the 1/16 brushless revo and have done most hopups and also have the castle motor conversion. It's great but feels like it breaks down way too often or not very resistant and I don't do flips...
  11. Thread: Speed Hawg 2.2

    by samk
    Replies
    5
    Views
    339

    yupp, those are in the wheels. I will remove the...

    yupp, those are in the wheels.
    I will remove the steel shaft return plastic maybe a slight bend in steel shaft is causing the problem
  12. Thread: Speed Hawg 2.2

    by samk
    Replies
    5
    Views
    339

    well the tap overlapped about half a centimeter....

    well the tap overlapped about half a centimeter.

    Maybe its loose did not check but they do not balloon.
  13. Thread: Speed Hawg 2.2

    by samk
    Replies
    5
    Views
    339

    Speed Hawg 2.2

    Need help from someone using them.

    I have speed hawgs and I taped the inside to prevent ballooning and that worked well.

    When I hit the throttle in the air they vibrate/wobble more than normal....
  14. Replies
    77
    Views
    4,192

    might work but to have to do that the design is...

    might work but to have to do that the design is not good. Whey could they not use screws instead of pins with rubber ring etc I just don't like them anymore. I am on my second set so its not cheap :(
  15. Replies
    77
    Views
    4,192

    thanks for the link. Still after using them and...

    thanks for the link. Still after using them and seeing that I can get the rings one way or another I did not like the fact that they bend easily after hitting a curb. (my fault) but in any case at...
  16. Replies
    1,514
    Views
    80,488

    careful with the rubber ring on the traxxas...

    careful with the rubber ring on the traxxas shaft.. they dry get weak and fly off or fall off. Might do with temps. we are like 35C over here :)
  17. Replies
    77
    Views
    4,192

    Hello, Maybe someone has some input on this :)...

    Hello,

    Maybe someone has some input on this :)

    I have the following and now regret having spent money getting them.

    Traxxas Steel Center Drive Shaft
    Traxxas Assembled Steel CV Driveshaft...
  18. Replies
    77
    Views
    4,192

    So far pretty good :cool:

    So far pretty good :cool:
  19. Replies
    77
    Views
    4,192

    Those barrel nuts are pretty cool! Bad...

    Those barrel nuts are pretty cool!

    Bad news.... so much for the titanium pivot balls... load of crap!

    Hit the curb doing maube 25 MPH and snaped in 2. Would have prefered if it bent so i can...
  20. Replies
    77
    Views
    4,192

    Thanks for the tips guys! I tested it today and...

    Thanks for the tips guys! I tested it today and it ran nicely and was stable!

    However, th knuckles are still getting loose :( Not as bad as HR but now with the dish wheels i need to remove the...
  21. Replies
    77
    Views
    4,192

    Ok finally after3 weeks i received my ...

    Ok finally after3 weeks i received my

    Pro-Line Speed Hawg II 2.2 tires and HPI Racing Dish Wheel Black 2.2 + glue.

    I washed the tires and next day i taped them and today glued them. I think...
  22. Replies
    3
    Views
    656

    Good to know guys!

    Good to know guys!
  23. Replies
    3
    Views
    656

    Traxxas Steel CV Driveshaft Set

    So i have been using them for some time and i also have a new pack in the box

    I notice that perhaps plastic is better! plastic bends but returns to straight and with the Steel CV Driveshafts not...
  24. Replies
    77
    Views
    4,192

    Did a quick test run on the street.... I find...

    Did a quick test run on the street....

    I find that the foam are not as good grippers and once it slides, i will be screwed haha so might need to find a wider street just in case.
  25. Replies
    77
    Views
    4,192

    Still not done yet. The kunckles from GPM are...

    Still not done yet. The kunckles from GPM are great but wish they would have added an extra threaded cap because they are a pain to screw on! One went in slightly angled and they are all very tight...
Results 1 to 25 of 175
Page 1 of 7 1 2 3 4