Search:

Type: Posts; User: jmartin

Search: Search took 0.01 seconds.

  1. Replies
    30
    Views
    1,119

    I was finally able to get it through. Does it...

    I was finally able to get it through. Does it matter if the 5145 pins stick out the other side by a few mm? I know some of you have cut them down a bit, but is that really necessary?

    Thank you.
  2. Replies
    30
    Views
    1,119

    Ok, I tried it on the other side of the truck...

    Ok, I tried it on the other side of the truck (right) and the pin goes right through. For some reason, the pin won't go through the left side. Maybe there's a small piece of metal or nick that...
  3. Replies
    30
    Views
    1,119

    I just came back from the hobby store, bought the...

    I just came back from the hobby store, bought the 5145 and those are too big as well. How can it fit on others and not on mine?
  4. Replies
    30
    Views
    1,119

    I bought some HPI screws and they don't fit the...

    I bought some HPI screws and they don't fit the rear of the Stampede, only the front. They're too big in diameter. Did anybody else experienced this? Will the Traxxas 5145 fit?
  5. Replies
    30
    Views
    1,119

    That's exactly what I was looking for. Thank you.

    That's exactly what I was looking for. Thank you.
  6. Replies
    30
    Views
    1,119

    I've done the blue loctite in the past and it...

    I've done the blue loctite in the past and it came undone again today which is why I'm asking the question. There's gotta be a better solution.

    I don't see how tape would last on there.
  7. Replies
    30
    Views
    1,119

    MIP x-duty problem

    I've been running the MIP x-duty CVD on my truck for a while now, busted the original ones not long after I got it. I've had this problem before where the end piece that attaches to the truck part...
  8. Castle Creations 1/8 Mamba Monster 2 Waterproof ESC 2650kV Motor V2

    I've been reading different threads about the Castle motors. I'm wondering if this one will be a good fit in my Stampede:

    Castle Creations 1/8 Mamba Monster 2 Waterproof ESC 2650kV Motor V2
    ...
  9. Replies
    30
    Views
    672

    Went to the store. They verified the new battery,...

    Went to the store. They verified the new battery, it's good.

    The problem seems to be with the ESC. Looks like I'll be buying a new ESC and Castle motor.
  10. Replies
    30
    Views
    672

    Here's an update. Battery fully charged, after 4...

    Here's an update. Battery fully charged, after 4 hours. I go out and run the truck for about 2 minutes, lots of power, incredible wheelies at high speed, everything is amazing. Then it's slows down...
  11. Replies
    30
    Views
    672

    What am I doing wrong then?

    What am I doing wrong then?
  12. Replies
    30
    Views
    672

    I have the Onyx 245 charger. I read somewhere...

    I have the Onyx 245 charger. I read somewhere that there is a 90 minute limit on one charge. I don't think I can set that up manually through the charger.

    There's not much to do on the charger...
  13. Replies
    30
    Views
    672

    I don't have the 2s batteries anymore, I threw...

    I don't have the 2s batteries anymore, I threw them out.

    I'm pretty sure it was slow blinking red and I'm pretty sure it was because of low voltage. I have the battery on charge right now. It ran...
  14. Replies
    30
    Views
    672

    New user question running 3s - How's my setup?

    I've had my Stampede 4x4 for a little while now. I ran two 2s (20C or 25C not sure) 5000 batteries in parallel but they both started to crack so I stopped using them. The hobby store told me the...
Results 1 to 14 of 14