Search:

Type: Posts; User: twisted metal

Page 1 of 5 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    44
    Views
    3,077

    Hey chris you get everything figured out??!!

    Hey chris you get everything figured out??!!
  2. Replies
    21
    Views
    1,525

    Is that comment one of sarcasim?

    Is that comment one of sarcasim?
  3. Replies
    21
    Views
    1,525

    Like I said it is 1/4- 20 threads, the same as...

    Like I said it is 1/4- 20 threads, the same as any big block. That nut to hold the flywheel on has nothing at all to do with what clutch you run.. I will post you a picture to show you have to...
  4. Replies
    21
    Views
    1,525

    You dont use the nut when you install a traxxas...

    You dont use the nut when you install a traxxas clutch on the tz. You use the 2.5mm hole in the end of the crankshaft as you would when installing a big block. The nut has nothing to do with what...
  5. Replies
    21
    Views
    1,525

    Yes dg stated that and im aware of the difference...

    Yes dg stated that and im aware of the difference in the crank. My point is you can put a tz sleeve in a tm, add the turbo button head and have urself a tz.

    As for not being able to run a traxxas...
  6. Replies
    21
    Views
    1,525

    they both run the 11k carb. no difference Im...

    they both run the 11k carb. no difference

    Im referring to dgs post talking about the 18 tm and the 18tz
  7. Replies
    21
    Views
    1,525

    The only difference in a tz and a tm is the...

    The only difference in a tz and a tm is the sleeve and the inner head button. Everything else is the same.
  8. Replies
    22
    Views
    1,013

    I have yet to figure out why people say the tz is...

    I have yet to figure out why people say the tz is hard to find parts for.. Parts for that engine are in stock almost everywhere.
  9. 18Tz hands down over the 21tm. The engine is...

    18Tz hands down over the 21tm. The engine is cheaper than the 21 and outperforms it.
  10. Replies
    44
    Views
    3,077

    Parts I recomend for what you are looking to do...

    Parts I recomend for what you are looking to do with your revo.

    * Traxxas bb kit- comes with the 40mm flywheel and the exhaust manifold. Also includes a few shims in which you will need to shim...
  11. My thoughts are if your engine is performing...

    My thoughts are if your engine is performing well, Run it theres no need to pull the engine down unless you are experiencing problems.
  12. Replies
    26
    Views
    1,357

    Heres what I think. I think your off to a great...

    Heres what I think. I think your off to a great start with the tune. The only problems I saw in the video was that you are lean on the hsn. When the truck shifts into second and you get a good clean...
  13. Replies
    3
    Views
    669

    I would suggest buying a glow driver and doing...

    I would suggest buying a glow driver and doing away with that part of the easy start. However if you rather not, check to make sure the harness is still grounded to the engine, the yellow wire. Make...
  14. Replies
    44
    Views
    3,077

    I hate to be the barrier of bad news, but the 21...

    I hate to be the barrier of bad news, but the 21 max is not a direct drop in. It runs turbo plugs and the mounting holes are different. You can use it however your going to have to purchase a bb...
  15. Replies
    7
    Views
    352

    anytime you have a high rev coming down like that...

    anytime you have a high rev coming down like that its usually a lean hsp
  16. Replies
    14
    Views
    651

    none the less you will be happy I promise!

    none the less you will be happy I promise!
  17. Replies
    5
    Views
    297

    they will hold just fine as long as they are not...

    they will hold just fine as long as they are not worn down to the spring, which from what I can see those arent
  18. Replies
    14
    Views
    651

    the cubic inches are there but the crankshaft...

    the cubic inches are there but the crankshaft deminsions are not that of a true bb. Thus being the reason the "drop ins" are considerd a mid-block
    the o.s 21 is not a true bb you will see the...
  19. Replies
    44
    Views
    3,077

    chris did you decided not to go with a big block?

    chris did you decided not to go with a big block?
  20. Replies
    0
    Views
    164

    Tell me what you guys think...

    I know its not neat and clean, but ive been wanting something to make my revo run upside down for an extended period of time, simply because im not always close by when it rolls over. This mod also...
  21. Replies
    0
    Views
    172

    Header tank. sinking line?

    Hey guys I need some info and a header tank setup, what tank where to mount, if its worth the trouble. I have also thought about the weighted or sinking line setup, all in hopes to prevent the air...
  22. Replies
    26
    Views
    642

    Yep they are fine, I get mine from there for 6...

    Yep they are fine, I get mine from there for 6 bucks shipped! It wouldnt be a bad idea to change the engine cradle and mount as well, there only about another 10 bucks. Ebay is my freind! lol
  23. Replies
    26
    Views
    642

    You can verify it by looking at it from the left...

    You can verify it by looking at it from the left side. The engine bay is not straight with the rest of the chassis. My guess is you landed upside, or during the flip it smacked the ground upside...
  24. Replies
    26
    Views
    642

    I hate to second whats already been stated since...

    I hate to second whats already been stated since your revo is fairly new, but sadly im pretty sure your chassis bent and theres only one true fix for that. A new one and a better brace.
  25. Replies
    11
    Views
    1,231

    Qoncepts?!?!?

    Has anyone heard anything about them lately? Or by chance where i can find a mount of theres. I dont understand why they went out.
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4