Search:

Type: Posts; User: hammertron2000

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    148

    Does anyone know if there would be a way to...

    Does anyone know if there would be a way to confirm the settings and maybe thats why it's not saving?
  2. Replies
    4
    Views
    148

    I replaced the batteries, still no luck. Anyone...

    I replaced the batteries, still no luck. Anyone else have some ideas? It's hard for me to ring traxxas because I'm in Australia.
  3. Replies
    4
    Views
    148

    I think a better way to explain it would be that...

    I think a better way to explain it would be that it allows me to adjust channels and settings but they reset after turning the car and radio off. Is there a way to save the adjustments so I don't...
  4. Yep I would agree, aluminum isn't the best option...

    Yep I would agree, aluminum isn't the best option because they bend, they're heavy, and can transfer damage to other parts. RPM is a lot better in my opinion.
  5. Replies
    37
    Views
    725

    This is how I've ended up. Gone from short course...

    This is how I've ended up. Gone from short course to crawling and back to short course. Started with a 2wd Slash when I was really young, a couple of years later bought a 1/16 slash, and then the...
  6. Motor Binding only at low speeds?

    Hi, just installed my Castle Creations 2200kv 1515 size motor, and it binds a little bit, but only at really really low speeds. Does anyone know if this is just how the motor turns over because thats...
  7. Replies
    4
    Views
    148

    Channel Reversing

    Hi guys, when I installed my Mamba Max X esc (and motor), and started it up, the steering channel was reversed. I went through the manual and found the process to reverse it (the radio/receiver is a...
  8. Replies
    14
    Views
    382

    Thanks for everyones help! I think I'll go the...

    Thanks for everyones help! I think I'll go the 2650.
  9. Replies
    14
    Views
    382

    What gearing do you run?

    What gearing do you run?
  10. Replies
    14
    Views
    382

    Would the 2650 on 4s, with 18/54 (maybe 18/52) in...

    Would the 2650 on 4s, with 18/54 (maybe 18/52) in a fully kitted 4x4 slash, overheat at all?
  11. Replies
    14
    Views
    382

    I have a question that will ultimately help me...

    I have a question that will ultimately help me decide. Lets assume same battery (4s 5000mAh 30c/40c), in a 4x4 slash, 18/54 gearing, what would the difference in speed be? At the moment I'm leaning...
  12. Replies
    14
    Views
    382

    ^*4s LiPo 5000mAh 40c

    ^*4s LiPo 5000mAh 40c
  13. Replies
    14
    Views
    382

    At the moment this is looking like the most...

    At the moment this is looking like the most likely combination.

    2200kv
    4s 500mah 40c
    18/54 gearing (maybe 19/54)
    External motor fan

    Any thoughts on that?
  14. Replies
    14
    Views
    382

    I will be using 4s; it'll have the durability...

    I will be using 4s; it'll have the durability upgrades.

    Still tossing up between the 2650 or the 2200. Let me get something straight. The 2200 has more torque, and is for slightly heavier...
  15. Replies
    14
    Views
    382

    At the moment I'm thinking this; Mamba Monster...

    At the moment I'm thinking this;

    Mamba Monster X with the 2200kv motor (instead of the 2650kv one).
    4s Lipo, or 6s lipo, not too sure?

    Anyone have any thoughts? 2200kv motor or 2650kv motor?...
  16. Replies
    14
    Views
    382

    Best Waterproof Motor/ESC Combo?

    Hi all, I'm looking at a Slash roller, will most likely buy stock Traxxas servo, transmitter, and receiver, but am looking for something with a bit more power, torque, and speed for the ESC and...
  17. Replies
    2
    Views
    281

    Slash complete.

    Hi guys. I've been focusing more on my scx10 project recently but now that thats done, I got back onto my 1/16 slash ^_^. I got it out and gave it a test drive (Hadn't been driven since the...
  18. sounds kinda cool, but I can't think of any...

    sounds kinda cool, but I can't think of any actual performance benefits. If you wanna do it, go for it!
  19. Replies
    14
    Views
    803

    Thanks for the feedback guys its been really...

    Thanks for the feedback guys its been really helpful!
  20. Replies
    14
    Views
    803

    Well I made my decision. Im going to get a...

    Well I made my decision. Im going to get a Slayer! My reasonings; I feel like im capable of it, and also whats the worst that can happen? Nitro isn't for me?, well, I'll covert it electric if worst...
  21. Replies
    14
    Views
    803

    Thanks for the awesome advice by the way, if I...

    Thanks for the awesome advice by the way, if I did buy a slayer, the manual should tell me everything I need to know anyway right?
  22. Replies
    14
    Views
    803

    Is it hard to learn? Or am I likely to mess it up...

    Is it hard to learn? Or am I likely to mess it up and blow the engine, because as I forgot to mention, I am only 16, , and even though I have pretty good mechanical knowledge and understanding, I...
  23. Replies
    14
    Views
    803

    Thanks for the feedback, I'm more interested to...

    Thanks for the feedback, I'm more interested to hear about what it's like to get into nitro. How do I tune it, break it in, maintain it properly? And all the things that differ from electric. Is...
  24. Replies
    14
    Views
    803

    Should I buy a Slayer?

    Hi. I've been thinking about getting a Slayer Pro 4x4 recently. It would be my first NITRO car, however I've got 3 other cars; a 1/16 slash, 2WD 1/10 Slash, and a 1/10 Axial SCX10. I have...
  25. Replies
    15
    Views
    363

    ok thank you. I have made progress by the way,...

    ok thank you. I have made progress by the way, opened up the center driveshaft and a connection had come loose, fixed that up and now its just the wheels and tires to go.
Results 1 to 25 of 448
Page 1 of 18 1 2 3 4